|
Title: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: ChrisKewl on July 07, 2012, 08:16:03 pm First I have to say I love the Obi110, I love having a home phone again. I have had Google Voice for a number of years, just never had a chance to tie it into something.
So, here is my problem. I followed this guide: http://voxilla.com/2011/02/15/how-to-obify-your-ip-phone-no-asterisk-involved/ It routes the call to my phone fine. However, I can't make calls. I get this error on the Obi110 status for the SP2 Service: Register Failed: 404 Not Found (server=192.168.1.199:5063; retry in 5s) I am using a DD-WRT router and my SPA-941 is at 192.168.1.199:5063, it is indeed open and working. If it wasn't then I wouldn't be able to receive calls. Any ideas? Am I going about this the wrong way? Also, I have 2 of these phones, any way I could route to both phones and be able to call with both phones? Thanks, Chris Haslage Title: Re: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: pc44 on July 12, 2012, 06:46:03 am Hi Chris,
I looked through the instructions in the link you provided. Are you sure you are supposed to be registering the OBI with your SPA-941? Unless I am misunderstanding the instructions (which I could be), inbound and outbound calling is performed without device registration. On the OBI, it appears as though you need to have, ProxyServer: 192.168.1.199 ProxyServerPort: 5063 RegistrarServer: [blank] X_RegisterEnable: Disabled After configuring that, test your outbound calls, and check the OBI System Status again. Let us know what happens, pc44 Title: Re: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: ChrisKewl on July 13, 2012, 11:17:40 am SP2 Service Status
Parameter Name Value OBiTALK Settings Status Registration Not Required help PrimaryProxyServer SecondaryProxyServer CallState 0 Active Calls I tried to call out on this phone with no luck so far. When I call with my SIP phone it still doesn't dial. Thanks. :) Title: Re: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: pc44 on July 13, 2012, 02:07:13 pm Could you provide the Status -> Call Status during your outgoing call attempt? While you are attempting to place the outgoing call via the Phone Port, if you refresh the Call Status page in your OBI several times, you should see some sort of information regarding the call.
pc44 Title: Re: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: ChrisKewl on July 17, 2012, 01:56:26 pm Tried this many times and the status doesn't change. I assume there has to be something up with my SPA941's configuration, but for the life of me I don't know.
Title: Re: Obi110 and Cisco SPA-941 without Soft-Phone Help Post by: hwittenb on July 19, 2012, 01:58:26 pm I don't believe the SPA941 is much different from my SPA3102. Most all the Cisco/Linksys devices are very similiar in the way they are configured. I tested my SPA3102 calling the OBi and making a call out using GV with the following configuration:
SPA3102 Line 1 Register: No Make Call Without Reg: Yes Proxy: 192.168.1.108:5069 where 192.168.1.108 is the ip address of the OBI, 5069 is the sip port number that I have configured for SP2 (X_UserAgentPort) UserID: hwittenb Dial plan: (xx.) OBi SP2 X_InboundCallRoute ({(hwittenb)>(xxxxxxxxxxx):SP1},{ph} where hwittenb is the userid configured on the SPA3102 above, SP1 is configured for GoogleVoice Using ip dialing I am calling SP2 on the OBi which bridges the call to SP1. |