OBi200 randomly reboot problem (reason 91)
glasgow:
It's been 10 days without reboot. So I guess the device with the new firmware is stable now? ;D
I am going to change the DigiMap and OutboundCallRoute to make it work according to my requirements. Will report back how it goes. And yes, if Robert can chime in and give me some suggestions regarding my settings that will be geat!
ianobi:
Robert seems to be taking a well earned rest - so I'll have a go at this one :)
Setting up a Trunk Group will do what you want. Dialling **1 or **2 will still force calls to sp1 and sp2 respectively.
Parameters should be as follows:
Physical Interfaces > PHONE Port > PrimaryLine: Trunk Group 1
Voice Service > Auto Attendant > PrimaryLine: Trunk Group 1
Voice Services > Gateways and Trunk Groups > Trunk Group1 >
TrunkList: sp2,sp1
DigitMap: ((Msp2)|(Msp1))
Voice Services > SP2 Service > X_NoRegNoCall: checked
SP1 DigitMap:
(*97|*98|4xxxS3|*225|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)
SP2 DigitMap:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.)
Nothing to do with the above, but I notice 933 is missing from here:
Phone Line DigitMap:
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|933|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))
glasgow:
Thank you very much ianobi!
ianobi:
I missed your requirement for routing of toll free numbers. There’s more than one way to sort this, but to route them normally via Voip.ms and also allow forcing them to GV by dialling **2, I suggest this:
User Settings > User Defined Digit Maps > User Defined Digit MapX >
Label: tfree
DigitMap: (18(00|88|77|66|55)xxxxxxx|<1>8(00|88|77|66|55)xxxxxxx)
Phone Line DigitMap:
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|933|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mtfree)|(Mpli))
Phone Line OutboundCallRoute:
{(911|933|(Mtfree)):sp1},{([1-9]x?*(Mpli)):pp},{(<##:>):li},{(<**70:>(Mli)):li},{(<**82:>(Mbt2)):bt2},{(<**81:>(Mbt)):bt},{(<**8:>(Mbt)):bt},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Msp3)):sp3},{(<**4:>(Msp4)):sp4},{(<**9:>(Mpp)):pp},{(Mpli):pli}
glasgow:
Thank you ianobi! I am still learning these settings so I have couple questions here.
1. Why you put "(Mfree)" in the phone line digitmap? I think "(Mpli)" is TG1's digitmap in my case so it has both Msp1 and Msp2 thus the toll free numbers are already included. Am I right?
2. Can I put 911|933 in Msp1 instead of in OutboundCallRoute because these two are exclusive for SP1?
Navigation
[0] Message Index
[#] Next page
[*] Previous page