Voice Gateway Account Setup

(1/5) > >>

Diana:
Spent the weekend setting my New OBi110 as follows:

Setup Google Voice on SP1 as my primary outgoing/incoming.  
Ported my T-Mobile@home Number to Google Voice.  This was done in 24-hours (exactly).  Since the number was already with T-Mobile, was NOT my mobile number, I was able to avoid having to transfer the number to a Pre-Paid Cell service.  They treated the number as if it was a Mobile Number!

Setup VOIP.ms on SP2 and will be using this line solely for e911:

Setup Voice Gateway1 for CallWithUs.  This is where I have some setup issues and need some assistance.  This Line will only be used to call a specify country, 876 and I need to be able to pickup the phone attached to the phone port and dial 1876XXXXXXX and these calls route through the gateway account 1 via CallWithUS.  How do I setup:

A) Phone Port DigitMap: (?)

|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**4(Mvg4)|**6(Mvg6)|**7(Mvg7)|**8(Mli)|**9(Mpp)|


and

B) PHONE Port OutboundCallRoute:(?)

{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**4:>(Mvg4)):vg4},
{(<**6:>(Mvg6)):vg6},{(<**7:>(Mvg7)):vg7},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}


per RonR's setup approach to achieve my objective?  Being a non-techie, A step by step outline would be very helpful.

Also, although I have VOIP.ms setup on SP2 and it shows it as Registered on the device status page when I'm connected to the device, the OBiTalk Dashboard shows it as "Not Configured" for Service Provider 2 and for Service Provider 1, it shows "Connected"?  I did all setup via the OBi110 directly and nothing was done from the OBitalk Portal.  

RonR:
Diana,

The bolded portions of the PHONE Port DigitMap and OutboundCallRoute are additions to the default values:


PHONE Port DigitMap:

|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**4(Mvg4)|**6(Mvg6)|**7(Mvg7)|**8(Mli)|**9(Mpp)|


PHONE Port OutboundCallRoute:

{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**4:>(Mvg4)):vg4},
{(<**6:>(Mvg6)):vg6},{(<**7:>(Mvg7)):vg7},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}


These additions establish the following dialing associations:

**3  ->  Voice Gateway3 (vg3)
**4  ->  Voice Gateway4 (vg4)
**6  ->  Voice Gateway6 (vg6)
**7  ->  Voice Gateway7 (vg7)


Assuming CallWithUs is configured on Voice Gateway3, you'd dial **3 + number to use CallWithUs.

If you'd like dialing 1876XXXXXXX to automatically go out Voice Gateway3, change:

Service Providers -> ITSP Profile A -> General -> DigitMap:

(<**3>1876xxxxxxx|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)

Diana:
Quote from: RonR on June 20, 2011, 11:47:45 am

Diana,

The bolded portions of the PHONE Port DigitMap and OutboundCallRoute are additions to the default values:


PHONE Port DigitMap:

|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**4(Mvg4)|**6(Mvg6)|**7(Mvg7)|**8(Mli)|**9(Mpp)|


PHONE Port OutboundCallRoute:

{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**4:>(Mvg4)):vg4},
{(<**6:>(Mvg6)):vg6},{(<**7:>(Mvg7)):vg7},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}


These additions establish the following dialing associations:

**3  ->  Voice Gateway3 (vg3)
**4  ->  Voice Gateway4 (vg4)
**6  ->  Voice Gateway6 (vg6)
**7  ->  Voice Gateway7 (vg7)


Assuming CallWithUs is configured on Voice Gateway3, you'd dial **3 + number to use CallWithUs.

If you'd like dialing 1876XXXXXXX to automatically go out Voice Gateway3, change:

Service Providers -> ITSP Profile A -> General -> DigitMap:

(<**3>1876xxxxxxx|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)



Thank you RonR.  I went ahead a use Voice Gateway 3 for CallWithUs.  The sections I'm having problems with now are the sections shown in bold bold:

Voice Gateway3 will be used with Callwithus:

Name : Callwithus
AccessNumber : SPx(sip.Callwithus.com)  (Is this exactly how it should be specify?)
DigitMap : (Mste)                                   (What should go here?)
AuthUserID : your_callwithus_user_id
AuthPassword : callwithus_password



And finally, let's configure the User Defined DigitMap referenced in Voice Gateway3:

Label : ste
DigitMap : (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1aaa>xxxxxxx|011xx.|(Mipd)|[^*]@@.'@'@@.)


Apparently we do not need a "User Defined DigitMap" in my case with a single Voice Gateway?  How do we reference the SP1 DigitMap above?  The Voice Gate setup is a bit confusing.  Thanks again for your help.

RonR:
Quote from: Diana on June 21, 2011, 06:59:29 am

AccessNumber : SPx(sip.Callwithus.com)  (Is this exactly how it should be specify?)


Since your SIP provider (VOIP.ms) is on SP2, you would need to use : SP2(sip.Callwithus.com)

Quote from: Diana on June 21, 2011, 06:59:29 am

DigitMap : (Mste)                                   (What should go here?)

And finally, let's configure the User Defined DigitMap referenced in Voice Gateway3:

Label : ste
DigitMap : (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1aaa>xxxxxxx|011xx.|(Mipd)|[^*]@@.'@'@@.)

Apparently we do not need a "User Defined DigitMap" in my case with a single Voice Gateway?  How do we reference the SP1 DigitMap above?


You could use:

VG3 DigitMap : (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1aaa>xxxxxxx|011xx.|(Mipd)|[^*]@@.'@'@@.)

instead of having it in a User Defined DigitMap and referencing it indirectly as (Mste), but you'll probably want to use it again elsewhere in the future so I'd keep it as described.

The SP1 DigitMap gets referenced from the PHONE Port DigitMap by **1(Msp1) and (Mpli).  (Mpli) refers to (Msp1) because you have the PHONE Port PrimaryLine set to SP1 Service.

Diana:
Thanks again RonR.  Everything is working great now.  The correct Digimap is:

(<**3:>1876xxxxxxx|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)

We were missing the ":" after the "**3", which sent the call out the CallWithUs Voice Gateway 3, but it was pre-appending the number 3 to 1876xxxxxxx.

One last issue I am having with VOIP.ms setup on SP2, is I am getting incoming calls to the Phone, but I having problems making ongoing calls.  I get a "486 Busy Here" when I dial 911 or a message saying "no call route available" when I dial **2+10-digit number.  Do you know what could be causing this issue?  Also, what should the port number for SP2 be...5060 or 5061?  I will do a search in the meantime to see if I can figure out what is calling the outgoing problem.  Thx!!!

Navigation

[0] Message Index

[#] Next page