Obion200-RouteByIPAddressoOrMACaddress
TommyRaton:
Service Providers -> ITSP Profile B -> SIP -> X_Proxy: Checked
There's a couple of X_Proxy somethings with check boxes but I'm not seeing a standalone X_Proxy
The forking is working now. Cell phone rings (have it only configured to ring one cell) as well as landline. I've lost the ability to dial out from the cell through CSipSimple, I'll keep working on it.
Thanks
azrobert:
Voice Services -> SP2 Service -> X_InboundCallRoute:
{OBixxx>(xx.):sp1},{ph}
The 1st rule will route outbound calls from your cell to SP1. Try dialing * to ring the OBi phone port. The xx. will match 1 or more digits, so * will not be routed to SP1 and the 2nd rule will ring the OBi. If it doesn't ring, check the CSipSimple configuration to make sure you have the correct IP address and port. The OBi SP2 default port is 5061. One method to block SIP scanners is to change the port number, so make sure the port number hasn't changed. It is found here:
Voice Services -> SP2 Service -> X_UserAgentPort
azrobert:
Quote
There's a couple of X_Proxy somethings with check boxes but I'm not seeing a standalone X_Proxy
I made a mistake. The proxy parm is found here:
Voice Services -> SP2 Service -> X_Proxy
TommyRaton:
Trying to make dialing with the * working to ring the obi phone/landline from the cellphone
Hope I'm correct in this but I have done nothing on the outgoing CSipSimple to "register" the cell phone with the OBi200. Should be able to ring the phone with * regardless
"Voice Services -> SP2 Service -> X_UserAgentPort"
As you suggested I took a look at the proxy port on line 2 and indeed the default with my Obi200 was 5081. This was changed to 5061. Still doesn't ring the Obi200 connected phone via dialing on CSipSimple with
X_InboundCallRoute = {obi200>(xx.):sp1},{ph} (Note obi200 double checked as the Username CSipSimple)
X_UserAgentPort = 5061
(Note there is a line X_UserAgentPorts as well which is blank)
X_KeepAliveServerPort =5060
azrobert:
Quote
Cell phone rings (have it only configured to ring one cell) as well as landline.
Half way there.
Quote
I've lost the ability to dial out from the cell through CSipSimple, I'll keep working on it.
Does this mean it worked, but now it doesn't?
Quote
Hope I'm correct in this but I have done nothing on the outgoing CSipSimple to "register" the cell phone with the OBi200. Should be able to ring the phone with * regardless
The cell should work without registration. I have this exact setup and it works for me.
Quote
As you suggested I took a look at the proxy port on line 2 and indeed the default with my Obi200 was 5081. This was changed to 5061. Still doesn't ring the Obi200 connected phone via dialing on CSipSimple
A port number mismatch will cause the call to fail. It should work now.
The name "obi200" is case sensitive and will cause outbound calls to fail if not an exact match. Will not prevent calling the OBi200 with "*".
For a test temporarily change the X_InboundCallRoute to ph and now dial 0 to ring the OBi200.
Is there any error message on CSipSimple when it fails?
Make sure the following is at the default of unchecked.
Voice Services -> SP2 service -> X_AcceptSipFromRegistrarOnly
I can't think of any other parm that would cause this to fail.
Everything should be at default except the parms I had you change.
I sure you checked this, but recheck if the IP address in the CSipSimple Proxy points to the OBi200.
Navigation
[0] Message Index
[#] Next page
[*] Previous page