Single-Stage Dialing Through Any OBi Trunk

<< < (4/9) > >>

eduMIA:
RonR as per your previous reply, you mentioned that this is possible:
- If you want to use two Google Voice accounts and be able to handle four calls, (each Google Voice account can handle two calls) you would want to use Trunk Group1 as your PrimaryLine.  Then when SP1 has two calls, calls number 3 and number four will go to SP2. Before I purchased the devices Obihai also mentioned that this will work.
I have configured and tested the gv accounts, the problem is that when making call3 instead of being handled by sp2 I get a service provider rejected the call, reason 503 message.
I called Obihai support line and the rep told me that trunk works as a "fail over", if sp1 is not working then it goes to sp2...!!!????
I have in the Outbound settings-Phone primary line the Trunk Group 1 and Trunk Group 1 has sp1,sp2 and is enable.
Am I missing something? Do I also have to configure DigitMap and OutboundCallRoute.?
Your help is appreciated!

RonR:
You don't need to modify the PHONE Port DigitMap or OutboundCallRoute to use Trunk Group1.

Trunk Group1 defaults to sp1,sp2.  You simply need to set:

Physical Interfaces -> PHONE Port -> PrimaryLine : Trunk Group 1

SP1 will be used for outgoing calls first, followed by SP2 if all sessions of SP1 are in use.

When you implement the changes described in this thread, replace {(Mcot)>(Mpli):pli} with {(Mcot)>(Mtg1):tg1} to have Trunk Group1 also used for single-stage dialing through the PrimaryLine.

lhm.:
Not working for me. I can dial out through the pap2 connected ObiOn-Pc App, works fine including **9 222 222 222 , just can't switch trunks. ie:**3  still tries to go out on tg1. The call log shows that **3 18005551212 is trying to go out on SP1 (part of tg1) which results in a busy signal as it is also sending **3. All other settings are per the RonR's instruction. Phone connected to Obi100 will switch trunks (**3 and **2) and connect/call fine including **9 222 222 222. Trying **2 gives the same result as **3. 

What am I missing? I am using only one Obi100 w/provisioning disabled.

ObiTalk
{(Mcot)>(Mtg1):tg1},{(Mcot)>(<*1:>(Msp1)):sp1},{(Mcot)>(<*2:>(Msp2)):sp2},{(Mcot)>(<*3:>(Mvg1)):vg1},{(Mcot)>(<*8:>(Mli)):li}, {(Mcot)>(<*9:>(Mpp)):pp},{(Mcot)>(<**1:>(Msp1)):sp1},{(Mcot)>(<**2:>(Msp2)):sp2},{(Mcot)>(<**3:>(Mvg1)):vg1},{(Mcot)>(<**8:>(Mli)):li},{(Mcot)>(<**9:>(Mpp)):pp},{(Mcot):aa},{ph}

AA DigitMap ([1-9]x?*@@.|[1-9]|[1-9][0-9]|<00:$1>|0|**1(Msp1)|**2(Msp2)|**9(Mpp)|(Mpli))          
AA OutboundCallRoute {([1-9]x?*@@.):pp},{0:ph},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**9:>(Mpp)):pp},{(Mpli):pli}      

Phone Port
DigitMap ([1-9]x?*@@.|[1-9]|[1-9][0-9]|911|**0|***|#|*1(Msp1)|*2(Msp2)|**3(Mvg1)|**2(Mvg2)|**6(Mvg6)|**7(Mvg7)|**9(Mpp)|(Mpli)|x.*x.)

OutboundCallRoute {([1-9]x?*@@.):pp},{**0:aa},{***:aa2},{(<*1:>(Msp1)):sp1},{(<*2:>(Msp2)):sp2},{(<**3:>(Mvg1)):vg1},{(<**2:>(Mvg2)):vg2}, {(<**6:>(Mvg6)):vg6},{(<**7:>(Mvg7)):vg7},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}

RonR:
lhm.,

What is the Trunk Group1 -> DigitMap?

lhm.:
Digit Map is (Msp1)

The Trunk List is sp1,sp2,vg1,vg2

Navigation

[0] Message Index

[#] Next page

[*] Previous page