Ports over pap2 dail plan to Obi100

(1/3) > >>

Dtan:
Please help me create a dial plan for Obi100

Setup:

SP1 : Google Voice
SP2: Callcentric

Pap2 dial plan:
(*xx.|*xxx|411:**275*18004664411>|<1877:**275*1877>xxxxxxxS0|<1866:**275*1866>xxxxxxxS0|<1800:**275*1800>xxxxxxxS0|<1888:**275*1888>xxxxxxxS0|<##:*123>|<:*75>xx<#:>|<*75xx|0|00|<:1614>[2-9]xxxxxx|<:1>[2-9]xxxxxxxxx|1[2-9]xxxxxxxxxS0|011[2-9]x.|[3469]11|**275*x.)


Need dial plan for SP1: 7 digits and 1+10 digits.

SP2: 911,411, and 1877,1866,1800,1888, voice mail dialing ##, 011, speed dial prefix *75

Thanks.

RonR:
There's a fair amount here and it's untested, so don't be surpised if it needs a tweak or two.


Physical Interfaces -> PHONE Port -> PrimaryLine : SP2 Service


Physical Interfaces -> PHONE Port -> OutboundCallRoute:

{([1-9]x?*(Mpli)):pp},{(<#:>):li},{911:sp2},{(*75xx):sp2},{**0:aa},{***:aa2},
{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}


Service Providers -> ITSP Profile A -> General -> DigitMap:

(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1614>xxxxxxx|011xx.|(Mipd)|[^*]@@.'@'@@.)


Service Providers -> ITSP Profile B -> General -> DigitMap:

(*xxx|*<00:75>xx|**275*[x*][x*].|<411:**275*18004664411>|<**275*>18(00|88|77|66|55)xxxxxxx|
<**275*1>8(00|88|77|66|55)xxxxxxx|<**1>1xxxxxxxxxx|<**11>[2-9]xxxxxxxxx|<**11614>xxxxxxx|
011xx.|(Mipd)|[^*]@@.'@'@@.)


           7-digits  ->  SP1 (1 + 614 + 7-digits)
         10-digits  ->  SP1 (1 + 10-digits)
         11-digits  ->  SP1 (11-digits)

                911  ->  SP2 (911)
               *xxx  ->  SP2 (*xxx)
             *00xx  ->  SP2 (*75xx)
         **275*+  ->  SP2 (**275*+)
                 411  ->  SP2 (**275*18004664411)
  800 + 7-digits  ->  SP2 (**275*1800 + 7-digits)
1800 + 7-digits  ->  SP2 (**275*1800 + 7-digits)
               011+  ->  SP2 (011+)


Note: Callcentric Speed Dials are accessed by *00xx to avoid conflict with OBi *75.
         Callcentric Voice Mail is accessed using *123 instead of ##.

Dtan:
Ron,

Thank you for the information. I will try it out once I receive my obi100 from Amazon.

BTW why SP2 was set as primary. Does it make a different when making or receiving a call which SP is primary ? I just want to learn more about the operation of the TA.

Thanks in advance.

RonR:
Incoming calls on any trunk will ring the OBi PHONE Port.

Outgoing calls are made by default on the PrimaryLine.  It doesn't matter what the PrimaryLine is as long as everything winds up going where it should.

In this instance, there are more special cases related to SP2 than SP1, so it's more convenient to make SP2 the PrimaryLine and redirect 7-, 10-, and 11-digit calls to SP1.  It could be rewritten with SP1 as the PrimaryLine, but there would be many more redirects to SP2 and it would look more complex.

Dtan:
Thanks, The setup works like a cham. BTW when I tried to dial out **2+plus 7 digits I got the error message there is no call route available.

How do I force dial SP2 ?

Thanks.

Navigation

[0] Message Index

[#] Next page