Bridge the call to SIP from Line-In using AA or by pressing any Key(* or #)
atikansari:
I just brought the Obi110 device and configured the Action VoIP on SP2.
There is an analog telephone connected to the OBi110 phone port.
There is PSTN line is connected to Line-In
My Default line is set to PSTN because my most of the calls are local and our local dialing pattern is 7 Digits(Eg# 893-xxxx).
I want to setup the dial plan that local calls should be go through PSTN and International(0091-xxxxxxxxxx or 0097-xxxxxxxxxx) call should be go through SIP account.
and I also want to call my line-in number from that bridge the call through my SIP account.
how can I achieve this, sorry I am newbie to VoIP. help will be appreciated.
RonR:
Quote from: atikansari on July 09, 2011, 11:54:59 pm
I want to setup the dial plan that local calls should be go through PSTN and International(0091-xxxxxxxxxx or 0097-xxxxxxxxxx) call should be go through SIP account.
Assuming you have Actionvoip configured and working on SP2 as discussed here:
http://www.obitalk.com/forum/index.php?topic=858.msg7182#msg7182
make the following additional change:
Physical Interfaces -> LINE Port -> DigitMap:
(xxxxxxxS4|<1>[2-9]xxxxxxxxx|1xxxxxxxxxx|<**2>011xx.|xx.)
7/10/11 digits -> PSTN (10-digits will have a leading 1 added)
011+ -> SP2 (011 will be changed to 00 when processed by SP2)
Quote from: atikansari on July 09, 2011, 11:54:59 pm
I also want to call my line-in number from that bridge the call through my SIP account.
To make calls out through Actionvoip from your PSTN line, you will have to go through the OBi Auto Attendant.
Do you have CallerID on incoming calls from your PSTN line? If so, you can have certain callers on the PSTN line go to the Auto Attendant and the rest ring the OBi phone. Without CallerID on the PSTN line, all calls will have to go to the Auto Attendent if you wish any to go there. Callers can still reach the OBi phone by pressing 1 at the Auto Attendant menu.
atikansari:
i don't have caller id feature, and when i call my home number auto attended not answering. How can i enable it and make the calls.
Thanks RonR for your great help. without your help i couldn't able to setup my device....many many thanks for your quick reply.
RonR:
To route all incoming calls on the LINE Port to the Auto Attendant, set:
Physical Interfaces -> LINE Port -> InboundCallRoute : aa
When the Auto Attendant answers, callers will be prompted to press:
1 to continue this call (ring the OBi phone)
2 to make a new call (make an outgoing call as if using the OBi phone)
3 to enter a callback number (have the Auto Attendant call you back after hanging up)
To allow only authorized callers to make outgoing calls, you may wish to PIN protect the Auto Attendant:
Voice Services -> Auto Attendant -> UsePIN : (checked)
Voice Services -> Auto Attendant -> PIN1 : (must be all digits)
NOTE: Due to a bug in the OBi firmware, you will not be able to enable Do Not Disturb (*78) or Call Forward All (*72) on the PHONE Port and still be able to reach the Auto Attendant from the LINE Port. If either of these features is used, all InboundCallRoute processing stops on the SP1, SP2, and LINE Port trunks, breaking the OBi's ability to use techniques such as reaching the Auto Attendant. Even though correcting the problem is extremely simple, I've been informed by Obihai they will not be fixing this bug.
atikansari:
thanks for your support to enable the AA but after connecting to AA from Line-In, I can't route the calls to SP2(VoIP provider). always getting invalid number.
even dial plan also not working on my phone. i can make local 7 digits call but i can't make the international calls using SP2. Any Idea.
Navigation
[0] Message Index
[#] Next page