Obihai 202 and Cisco SPA504G setup problem
Torress:
Hello,
I am trying to setup Obitalk with Google Voice to SPA504G and the ip phone showing Initialing Network everything. I plugged the Obiahi202 internet to router (Comcast) and SW port between Obi device to Cisco ip phone. What should I do ? Can anyone help me to setup ?
Thanks
drgeoff:
Maybe http://web.archive.org/web/20160317011451/http://www.obihai.com/docs/OBi-VoIP-Device-Attach-Legacy-IP-Phone-Workbook-v1-0.pdf helps you.
Torress:
I tried to change the Obi setting and IP phone settings it says "Not Registered. (No Response) on the IP Phone display. Any idea ?
drgeoff:
Quote from: Torress on August 11, 2016, 02:22:20 pm
I tried to change the Obi setting and IP phone settings it says "Not Registered. (No Response) on the IP Phone display. Any idea ?
Do you really expect that with so little info about what you have actually done in quite a complex setup anyone can identify the problem?
Are you following to the letter the document I linked to? The only idea I have is to check that you have changed the appropriate SP slot on the OBi202 from being a SIP client to acting as a SIP proxy.
Torress:
I configured the Obi202 and SPA504G setting on Web Guide Interface. I made the following changes:
And so, ITSP Profile D and SP4 on the OBi202 shall be configured as a proxy for the IP phone.
ITSP Profile D/General/SignalingProtocol = SIP (default)
ITSP Profile D/SIP/ProxyServer = 192.168.1.10 (ie IP address of our SPA962 IP Phone)
ITSP Profile D/SIP/ProxyServerPort = 5063 (SIP listening port for our IP Phone)
ITSP Profile D/SIP/X_SpoofCallerID = yes (or checked, this will ensure we pass the caller ID through)
Next, create the local voice service that the IP phone will use as its proxy:
SP4/X_ServProvProfile = D (Were saying use the ITSP D profile with this voice service)
SP4/X_UserAgentPort = 5063 (Note:'you'can'choose'a'port'that'you'prefer,'just'be'sure'to'use'the'
same'port'number'throughout'the'tutorial
SP4/X_RingProfile = B
SP4/X_RegisterEnable = no (or unchecked)
SP4/AuthUserName = 1001 (This can be defined by you, but needs to be the same on the IP Phone)
SP4/AuthPassword = AnyPhonePassword (Once again, you can define this, but must be the same on
the IP Phone)
SP4/X_Proxy = yes (or checked)
Configure the IP phone to register to the OBi and use it as its proxy
On the IP phone, set=up the following parameters:
EXT 1/Proxy = 192.168.1.20:5063 (ie: IP address of OBi202)
EXT 1/User ID = 1001
EXT 1/Password = AnyPhonePassword
EXT 1/Register Expires = 60
EXT 1/Register = yes
SIP/Send Resp To Src Port = yes
When i did the changes and reboot of the devices, SPA504G phones buttons became solid green and when i hang up the phone there is a dial tone i guess which is a good sign. I tried to follow instructions on obitalk to add a device it asks me to call ** number. When i try to dial two star codes it says InvalidNumber on the phone display. I also try 1 star code (*)+number it says Busy when i dial. I couldnt add the device because of the InvalidNumber error. I plugged both Obi202 and Cisco IP phone to modem. Please advice and thanks.
Navigation
[0] Message Index
[#] Next page