Using SipToSis to Make and Receive Skype Calls Through an OBi
ccclapp:
hi all,
Thanks for this thread. I've been trying to follow these instructions and has made some progress but not enough to get to the finish line. Here are my specific questions/problems:
Quote
Add the OBi's SPx IP address in SkypeToSipAuth.props (SPx must be configured as SIP):
*,sip:siptosis@192.168.1.150:5061,YourSkypeUserID // :5060 = SP1 | :5061 = SP2
which IP address to I use, the one listed under LAN or WAN? For your reference I only have the Internet port on my OB connected. Thus, the only meaningful IP I have is the WAN IP. This is the same as what my Comcast router shows as it's given DHCP address for the OB.having said that, in the OB web access under router configuration > LAN settings I see a different IP address. I have tried both in the SkypeToSipAuth file. Please note: when I run the BAT file everything seems fine except my second to last line always says "STUN: error – unknown host: stun.xten.net
Next, I make these edits:
Quote
SP2/ITSP Profile B should have ALL settings at Default except for:
Service Providers -> ITSP Profile B -> SIP -> ProxyServer : 127.0.0.1
Voice Services -> SP2 Service -> AuthUserName : (put anything here)
Voice Services -> SP2 Service -> X_RegisterEnable : (unchecked)
Voice Services -> SP2 Service -> X_ServProvProfile : B
SP2 status should show : Registration Not Required
I boot after every edit. Following this for SP2 service status initially I get "registration not required", but after a minute or two the status changes to "service not configured". Ivory tried this several times and it always reverts back to not configured status.
I have also copied and pasted your full digimap lines but continue to have the two problems listed above.
When you say
Quote
Voice Services -> SP2 Service -> AuthUserName : (put anything here)
do you literally mean put anything there or does it have to be something meaningful?
I'm trying to literally follow your directions Word for Word as this is somewhat foreign to me. Assuming you've truly listed all the steps and I can copy and paste your digital map text in full, I'm not sure what I'm doing wrong.
Have you omitted any steps or assumed the user has some independent knowledge, because I am just copying exactly what you wrote.
Thanks very much it sure would be great to get this working!
QBZappy:
Quote from: ccclapp on August 15, 2012, 09:42:28 pm
Please note: when I run the BAT file everything seems fine except my second to last line always says "STUN: error – unknown host: stun.xten.net
Go to command prompt and ping stun.xten.net (times out)
Now try this stun server: ping stun.sipgate.net (this one returns TTL info)
List of stun servers: http://www.voip-info.org/wiki/view/STUN
ccclapp:
Hi
Thanks for the reply.
Im sorry, but I dont understand what you are saying and why. I am very new at all of this. Isnt my issue likely what IP I should be using in the SkypeToSipAuth.props file edits?
I am trying to use SipToSis for Skype Calls Through an OBi. I had questions about the directions posted. What would pinging a sipgate address have to do with this?
Sorry, I dont understand.
Thanks
QBZappy:
ccclapp,
You are right, your main issue is something else.
Just pointing out that the stun server stun.xten.net does not seem to be working. The ping was just how to test if the stun server would reply.
I haven't used siptosis in over a year. Try entering the ip address returned by dialing ***1 on the phone connected to the OBi.
ccclapp:
GOOD NEWS, IT'S WORKING (99%)!! Lots of thanks to RonR JoeinForum and everyone else who help with this. I'll ask a couple of questions and then will write a how-to for dummies for the next person who, like me might have little background in this. First, (selfishly) my questions:
Everything is working, (plus as I will describe I've added a sip client and edited the DigitMap accordingly). However, the following issues remain:
1. with Skype, when I can call out everything is fine, however, incoming calls trigger siptosis which seems to see the call and then immediately disconnects after ringing once on the computer and never ringing on the OBIHAI phone. Any ideas why this may be? Attached is a screenshot showing a) A typical error I get when executing the bat file (shown on the top line). b) The log of when calling into Skype. any diagnosis of this would be appreciated!!
EDIT: forum uploader is full so screenshot not attached
2. When calling out from the OBIHAI phone via Skype, sometimes the call recipient cannot hear me. If I push a key on the dial pad generating a tone they can hear me following that. Does this make sense? Is there something I can do to overcome this? Is there something wrong with my configuration? Possibly related, if an OBIHAI Skype call is underway I often hear it both on my hard phone and on the Skype computer phone. If I push the keypad on the computer I also hear that tone. Is it normal to have sounds across both the computer and the OBIHAI phone?
3. I don't understand the DigitMap phraseology and just copied what RonR posted. I observed the following:
a. the references for service providers beyond number two were removed so when I added a sip service provider as SA3 I reentered this manually.
b. He uses "#1...#" to trigger service provider 2, where OBIHAI's default language uses **2, I haven't done it yet but will likely change this back so everything is consistent.
I think that's it for questions/comments other than THANK YOU GUYS VERY VERY MUCH!
Now I'll post my how-to for dummies in the next post…
Navigation
[0] Message Index
[#] Next page
[*] Previous page