Setting up Obi200 - DigitMap
azrobert:
If your Phone PrimaryLine is SP2, change it to SP1 or remove "{(Mpli):pli}".
dima:
Quote from: azrobert on January 09, 2017, 05:57:16 am
If your Phone PrimaryLine is SP2, change it to SP1 or remove "{(Mpli):pli}".
if I have the following, do I still need to remove "{(Mpli):pli}" ?
SP1 = freephoneline.ca = Registered
SP2 = Google Voice = Connected
I found that if I dial '1' in front of Canadian number, then it uses GV to dial out. but if I dial same number without '1' then it uses FPL. I didn't try to dial US number without '1'.
thank you.
dima:
To refresh what I have:
Phone1 ->
digitMap:
([1-9]S9|[1-9][0-9]S9|*98|211|311|911|1xxxxxxxxxx|[2-9]xxxxxxxxx|011xx.S3|00xx.S3|**0|***|222222222|**[1-3]xx.S3)
outbound call route:
{**0:aa},{***:aa2},{222222222:pp},{(Msp1):sp1},{(Msp2):sp2}
CallReturnDigitMap:
{pli:(xx.)},{sp1:(<**1>xx.)},{sp2:(<**2>xx.)},{sp3:(<**3>xx.)},{sp4:(<**4>xx.)},{bt:(<**8>xx.)},{bt2:(<**82>xx.)},{pp:(<**9>xx.)}
ITSP Profile A General -> DigitMap:
(<1>(236|250|778|403|587|780|825|306|639|204|431|416|437|647|807|249|705|226|519|548|289 |365|905|343|613|418|581|450|579|438|514|819|873|709|506|782|902|867)xxxxxxx|(236|250|778|403|587|780|825|306|639|204|431|416|437|647|807|249|705|226|519|548|289 |365|905|343|613|418|581|450|579|438|514|819|873|709|506|782|902|867)xxxxxxx|<**1:>xx.|18(00|88|77|66|55|44)xxxxxxx|*98|911|933)
Primary Line: SP1 Service
Thanks.
azrobert:
Ignore my last post.
Try this:
Physical interfaces - PHONE 1
DigitMap:
([1-9]S9|[1-9][0-9]S9|*98|211|311|911|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.S3|00xx.S3|**0|***|222222222|**[1-3]xx.S3)
Service Provider -> ITSP Profile A -> DigitMap:
(1 (236|250|778|403|587|780|825|306|639|204|431|416|437|647|807|249|705|226|519|548|289
|365|905|343|613|418|581|450|579|438|514|819|873|709|506|782|902|867)xxxxxxx|<**1:>xx.|18(00|88|77|66|55|44)xxxxxxx|*98|911|933)
You weren't checking for 11 digit numbers. I changed the phone digit map to convert 10 digit numbers to 11. Now you only have to check for 11 digits in the "A" digit map.
dima:
Perfect! It works just the way I wanted it. Thank you very much! You're the best!
Final config if someone wants to re-use it:
Physical interfaces - PHONE 1
--> DigitMap:
([1-9]S9|[1-9][0-9]S9|*98|211|311|911|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.S3|00xx.S3|**0|***|222222222|**[1-3]xx.S3)
--> OutboundCallRoute:
{**0:aa},{***:aa2},{222222222:pp},{(Msp1)):sp1},{(Msp2)):sp2}
Service Provider -> ITSP Profile A -> DigitMap:
(1(236|250|778|403|587|780|825|306|639|204|431|416|437|647|807|249|705|226|519|548|289|365|905|343|613|418|581|450|579|438|514|819|873|709|506|782|902|867)xxxxxxx|(236|250|778|403|587|780|825|306|639|204|431|416|437|647|807|249|705|226|519|548|289|365|905|343|613|418|581|450|579|438|514|819|873|709|506|782|902|867)xxxxxxx|<**1:>xx.|18(00|88|77|66|55|44)xxxxxxx|*98|911|933)
Service Provider -> ITSP Profile B -> DigitMap:
(1xxxxxxxxxx|[2-9]xxxxxxxxx|<**2:>xx.)
Navigation
[0] Message Index
[*] Previous page