Authentication error [fixed]
Marc:
Quote from: Taoman on August 11, 2017, 07:16:40 am
Quote from: Webslinger on August 11, 2017, 07:13:59 am
Would be useful if people stated what model ATAs and firmware versions they're using.
Agreed. What OBi devices are you using?
I am connecting directly with an OBi 200 with no issues. Inbound and outbound calls work fine. I've rebooted with no issues.
I also use the Simonics GV gateway with my OBi 110 without any issues.
Are you connected directly to your gvoice accounts, using the built-in oauth? Or do you have other SPs setup also? GV is the only service having a problem. I have accounts with Callcentric, and a couple of other SIP services that are working without a problem. I'm just manually selecting one of those SPs to make calls now (**(sp#), ie: **2 1-212-555-1212)
The newest firmware does NOT have a fix for this problem. I updated 2 202's to it this AM with no change.
A_Friend:
I have two devices, a 200 and a 202, each with different GV numbers. Or, at least I did. Both failing to register this morning.
The GV number assigned to the 200 is set up to ring, so no outgoing and incoming going straight to voicemail. If this persists, I'll reroute it. The 202 is only used for outgoing, its GV number rings to my main callcentric number
(My voip.ms and callcentric accounts are just fine, so I'm not incommunicado, just paying for outgoing calls like regular muggles.)
I run both devices with Obitalk off, so no firmware upgrades in a while.
Freshmaker:
Quote from: dvpatel on August 11, 2017, 07:19:19 am
Ditto.
I run the same FW and I do not think the new FW has a fix.
Quote from: Freshmaker on August 11, 2017, 07:16:56 am
I have an Obi200 with firmware 3.1.1 (Build: 5463EX) and am having the same OAuth issue. Are you saying this is a known issue that was fixed in 5695EX?
I dialed "***6" on my phone and it says "Software update not available"...so I am assuming 5463EX is the current firmware for the Obi200.
dvpatel:
I had 3 lines configured on my OBi 200.
Two were showing as disconnected. One was showing as connected. When I rebooted to fix the two broken ones, the one that was showing as connected started showing as disconnected.
I dropped one of the lines that was showing as disconnected. Now I cannot add it back due to the Auth error that people are getting.
Quote from: Taoman on August 11, 2017, 07:16:40 am
Quote from: Webslinger on August 11, 2017, 07:13:59 am
Would be useful if people stated what model ATAs and firmware versions they're using.
Agreed. What OBi devices are you using?
I am connecting directly with an OBi 200 with no issues. Inbound and outbound calls work fine. I've rebooted with no issues.
I also use the Simonics GV gateway with my OBi 110 without any issues.
Edit: I am using 3.1.1 (Build: 5657) fw on my OBi 200 which is still working fine with GV.
Webslinger:
Quote from: Marc on August 11, 2017, 07:15:41 am
I have the latest firmware, 5695EX on my 202's. This isn't just a 100/110 issue. I have multiple 200's & 202's, GV has stopped working on all of them, as of this AM.
All the OBi200/202 ATAs I see that still work with GV have the following settings disabled:
Under System Management-->Auto Provisioning
a) For Auto Firmware Update ---> disabled
b) For ITSP Provisioning ---> disabled
c) For OBiTalk Provisioning--->disabled
d) Voice Services-->OBiTALK Service-->Obitalk service Settings disabled
So, Obitalk.com has not able to communicate with these ATAs, after they were provisioned, and they're all using 3.1.1 (Build: 5695EX).
If you disable Obitalk service and Obitalk Provisioning you will not be able to provision Google Voice using Obitalk.com.
Navigation
[0] Message Index
[#] Next page
[*] Previous page