Simple config OBi110 to Mac Softphone
042DYA:
Thanks DRGEOFF. I did what you said but no luck. I reset the OBi110 to factory defaults and then changed only what you stated in the post. I have use of a Windows PC too to check configuration, so under Windows, do you have a softphone client and config for that to recommend?
SteveInWA:
The SIP 486 error you are getting means "Busy here". Ignoring the softphone for the moment, if your POTS line is plugged into the LINE port on the OBi, can you make and answer calls on it, using a standard analog telephone plugged into the phone jack on the OBi?
042DYA:
Yes, using a standard analog phone, I can both dial and answer using the phone port on the OBi110.
azrobert:
Quote from: 042DYA on October 29, 2017, 12:00:37 pm
I have use of a Windows PC too to check configuration, so under Windows, do you have a softphone client and config for that to recommend?
I already had written the following for another user and didn't feel like changing it to SP1. If you are going to define GV on the OBi110, I think it makes more sense defining GV on SP1.
OBi110:
Service Providers -> ITSP Profile B -> SIP -> ProxyServer: 127.0.0.1
Service Providers -> ITSP Profile B SIP -> X_SpoofCallerID: Checked
Voice Services -> SP2 Service -> AuthUserName: OBi110
Voice Services -> SP2 Service -> X_RegisterEnable: unchecked
Voice Services -> SP2 Service -> X_ServProvProfile: B
Voice Services -> SP2 Service -> X_InboundCallRoute:
{OBi110:li},{ph}
Physical Interfaces -> Line Port -> InboundCallRoute:
ph,sp2(0@192.168.1.100:5060)
Change 192.168.1.100 to the IP address of the computer running Phonerlite.
5060 is the Port number for Phonerlite
Download and install Phonerlite:
http://www.phoner.de/PhonerLiteSetup.exe
When you start Phonerlite I think a wizard will popup because no accounts are defined.
Proxy: 192.168.1.100:5061 (IP addr & Port of SP2 on the OBi110)
Click right arrow.
User Name: OBi110
Click right arrow.
Change Profile Name: OBi110
Click check mark
Uncheck box next to Register
Save
Dial a number and click the green phone symbol.
You can use the keyboard to dial a number.
Click red phone symbol to hang up.
azrobert:
Quote from: 042DYA on October 29, 2017, 12:00:37 pm
Thanks DRGEOFF. I did what you said but no luck.
drgeoff forgot the SP1 X_InboundCallRoute. When making a call with that config, the phone port will ring instead of routing the call to Line. If you don't have a phone plugged into the OBi110, a flashing phone port LED will indicate ringing. This will prove you are communicating with the OBi110.
I have Zoiper installed on Windows and I had more trouble getting it to work properly than any other softphone.
Here is my config:
SIP
Domain: 192.168.1.xxx:5061 (OBi110 IP and SP2 port)
UserName: OBi110
Password: anything
Outbound
Auth UserName: OBi110
Use outbound proxy: checked
Outbound proxy: 192.168.1.xxx:5061
Zoiper can't register to an OBi110, so click the tab "Unregister"
This configuration should allow you to make outbound calls, but with audio problems. I had a one-way audio problem. I don't have time right now, maybe later tonight. I have to think about what I did to correct the audio problems.
Navigation
[0] Message Index
[#] Next page
[*] Previous page