OBI200 doesn't work with firmware version 3.2.1
drgeoff:
Yes, I've just noticed the yellow triangle against my OBi1032 phone whose support expired more than 2 years ago. It is less than 2 weeks since I did a manual update.
But clicking the yellow triangle didn't update the firmware. Possibly because I have remote provisioning disabled. So I tried again and as advised in the text box I clicked cancel to take me to the manual update method. That turned out to be the standard download page on the forum. Downloaded the "latest" there to a PC and looked inside. It is 5.04 4003EX. Way behind the 5.0.8 4643 already in the phone.
And the ***6 method on the phone reports no update available.
???
GPz1100:
From this thread - https://www.obitalk.com/forum/index.php?topic=9983.msg84134#msg84134 , here's the direct link.
http://fw.obihai.com/OBi202-3-2-1-5757EX.fw
powaking:
Similar issue. Been working fine then just the other day no dial tone. Tried resetting which worked and brought be back to 3.1.1. Then it said there was a new update. Pressed the triangle and now back to not working. Power it on and the power light is on solid for a few seconds, starts to flash then power light goes out. Unable to reset it. What I have tried:
Reset pin>plugged in power>lights flash quickly>lights go out and back on>flashes>goes out>release pin
Reset pin>plugged in power>lights flash quickly>release pin>lights go out and back on>flashes>goes out
Tried the above with a different power supply that provides 12v. No difference. I feel like Obihai pushed out an update which I clearly did not need and then bricked my device. Its no longer under warranty but now am forced to purchase another one.
SteveInWA:
Quote from: powaking on November 26, 2017, 07:03:09 pm
Similar issue. Been working fine then just the other day no dial tone. Tried resetting which worked and brought be back to 3.1.1. Then it said there was a new update. Pressed the triangle and now back to not working. Power it on and the power light is on solid for a few seconds, starts to flash then power light goes out. Unable to reset it. What I have tried:
Reset pin>plugged in power>lights flash quickly>lights go out and back on>flashes>goes out>release pin
Reset pin>plugged in power>lights flash quickly>release pin>lights go out and back on>flashes>goes out
Tried the above with a different power supply that provides 12v. No difference. I feel like Obihai pushed out an update which I clearly did not need and then bricked my device. Its no longer under warranty but now am forced to purchase another one.
To be very clear: are you saying that now, after you have performed the factory reset, and you power off and then power on the device, and just let it sit there, that all three of the LEDs are off (none are blinking)? If that's the case, then you have a hardware failure. A failed firmware download can't do that. The expected behavior after a failed firmware installation is that the left-most (power) LED is alternatively-blinking red and green. The hardware has just enough "smarts" to start up and put itself in recovery mode, even if the firmware load is bad.
If you have the red/green blinking LED, you can recover from it. If no LEDs are lit, then your device is dead, or it's power adapter is dead. You can try swapping a different power adapter, if you have a 12VDC "wall wart power adapter with the same "barrel" connector.
powaking:
When I plug it in the power light is solid, after a few seconds it starts to flash and then the power light goes out. The ethernet light continues to flash based broadcast traffic. Device is not pingable in any way. This all started about a week ago, don't recall exact date. I was able to get it resurrected but that was only once then it looked like a firmware was pushed to it (I've been running 3.1.1 for as long as I remember).
Navigation
[0] Message Index
[#] Next page
[*] Previous page