Transfer from PSTN to another OBI
A_Friend:
Quote from: jerome on July 19, 2018, 12:47:29 pm
Not Only make a call from France (with trusted list), but also ring the GV on SP1 in OBI200 (USA)
So... You want to ring the PHONE attached to the Obi200, right? And it has another carrier on SP2?
There are 4 SPs on the Obi200, and one phone port. You can ring the phone with any of those SPs.
You dial in to SP2, the phone rings. Or, if you dial into AutoAttendant, you press "1" and the phone rings.
Ringing the phone doesn't have to have anything to do with Google Voice.
jerome:
Quote from: A_Friend on July 19, 2018, 12:54:56 pm
Quote from: jerome on July 19, 2018, 12:47:29 pm
Not Only make a call from France (with trusted list), but also ring the GV on SP1 in OBI200 (USA)
So... You want to ring the PHONE attached to the Obi200, right? And it has another carrier on SP2?
There are 4 SPs on the Obi200, and one phone port. You can ring the phone with any of those SPs.
You dial in to SP2, the phone rings. Or, if you dial into AutoAttendant, you press "1" and the phone rings.
Ringing the phone doesn't have to have anything to do with Google Voice.
When call from the Line on Obi110, I want the OBI110 (phone attached), the OBi200 (phone attach and the SP1) to ring, if this not a trusted caller if this is the trusted caller then aa.
hope it is clear
Thank you
Jerome
A_Friend:
Which is the voip carrier you're using? Do you have DIDs from that carrier?
jerome:
Quote from: A_Friend on July 19, 2018, 01:45:30 pm
Which is the voip carrier you're using? Do you have DIDs from that carrier?
Obi110 has phone line and Sp with Callwithus
Obi200 has SP1 GV and Sp2 Callwithus
no did
-J
A_Friend:
OK, I just spent a few minutes on callwithus' website, and I can't figure out if they have the features you need to do this. You probably do, but either way, I'm going to use an example how I'd do it with Callcentric.
Callcentric gives you an 11 digit account number of the form 17771234567. You can create extensions, too. For the sake of argument, let's say you've set these up as 101, 102, and 103. They also have longer names, based on your account number, i.e. 17771234567101, 17771234567102, etc. The short numbers are useful for dialing. The long numbers are needed for their Call Treatment features, I think.
With either of these, you have a choice of using the device to do sequential ring, or using their website to do simultaneous ring.
Sequential ring is accomplished by setting the CallForwardOnNoAnswer fields on the LINE port. Let's say after 4 rings you want it to forward to the Obi200. So in the CallForwardOnNoAnswerNumber field, you'd put SP2(101), which you've cleverly programmed on the Obi200 to receive the calls, probably on SP2.
So an incoming call would ring on the Obi110 for 4 rings and if not answered, would ring on the Obi200 where it could be answered.
Now, to do simultaneous ring, you need to use both SPs on the 110 and one on the 200.
You'd forward LINE to SP1 where it would call 17771234567. On the Callcentric website, you would set up a Call Treatment that said to simultaneously ring extensions 101 and 102 (which you've installed on the Obi110 SP2).
That said, I'm not sure how you handle AutoAttendant with this situation. If AutoAttendant picks up, the Obi110 stops ringing. You'll also need to pass a callerID from the line port. Don't have a 110, so don't know how possible that is.
Anyway, see if any of this translates to CallWithUs.
Good luck.
Navigation
[0] Message Index
[#] Next page
[*] Previous page