Routing li1 Calls Between obi212 and obi202 Devices
azrobert:
I never used MOH, so I can't help on this question.
You can setup a trunk group for 911. I'm assuming you are using Callcentric on SP4 for 911.
Modify the TG1 trunk list to: sp4,li
Add the following to the beginning of the phone OutboundCallRoute:
{911:tg1},
Add 911 to the Line and SP4 DigitMaps.
On the SP4 Service check X_NoRegNoCall
When 911 fails for SP4 the OBi212 will route the call to Line.
Conference and Transfer are standard features on all OBi's.
When on an active call, press Flash.
You will get a dial tone.
Call another number.
Hang up to transfer or Flash to conference.
You can setup rules to call the OBi202 phone ports.
Have you setup your OBi212 and OBi202?
dboling:
Quote from: azrobert on August 30, 2018, 11:07:42 am
I never used MOH, so I can't help on this question.
You can setup a trunk group for 911. I'm assuming you are using Callcentric on SP4 for 911.
Modify the TG1 trunk list to: sp4,li
Add the following to the beginning of the phone OutboundCallRoute:
{911:tg1},
Add 911 to the Line and SP4 DigitMaps.
On the SP4 Service check X_NoRegNoCall
When 911 fails for SP4 the OBi212 will route the call to Line.
Conference and Transfer are standard features on all OBi's.
When on an active call, press Flash.
You will get a dial tone.
Call another number.
Hang up to transfer or Flash to conference.
You can setup rules to call the OBi202 phone ports.
Have you setup your OBi212 and OBi202?
They just arrived in the mail 30 minutes ago. Configuring 202 now. usb-wifi won't be here until tomorrow.
Does the obi retrive GV voicemails ?
azrobert:
Call your own GV number to get the GV IVR. VM is one of the options.
dboling:
Quote from: azrobert on August 27, 2018, 09:05:22 am
I didn't read your post closely and didn't realize you're using all 4 SP slots, so you don't have a free slot for a dummy trunk. However, you can use SP4 for both Callcentric and routing calls between units. When you route calls between OBi's and the receiving SP trunk is registered to a provider, you will have audio problems. Turning off discovering your public IP will fix the audio problem. You can setup a voice gateway on the OBi202 for routing outbound to Line.
OBi212 Line InboundCallRoute: ph,sp4(0@xx.xx.xx.xx:pppp)
xx.xx.xx.xx = IP address of OBi202
pppp = X_UserAgentPort of OBi202 SP4 Service
ITSP Profile D SIP
X_SpoofCallerID: Checked
Needed to pass CallerID
OBi202
ITSP Profile D SIP
X_DiscoverPublicAddress: Unchecked
Now that the OBI202 and OBI212 have been installed I tried this configuration, however it does not work.
# Device IPs
OBI202: 192.168.3.61
OBI212: 192.168.3.60
SP4: Callcentric on both devices
## OBI212 Config
Physical Interfaces>LINE Port
InboundCallRoute: ph,sp4(0@192.168.3.61:5083)
Service Providers>ITSP Profile D>SIP
X_SpoofCallerID: Checked
## OBI202 Config
Service Providers>ITSP Profile D>SIP
X_DiscoverPublicAddress: Unchecked
Voice Services>SP4 Service
X_UserAgentPort: 5083
## Error Message from OBI212 Call History.
Call 1 09/01/2018 09:29:59
09:29:59 From LI1() Fork to:
PH1
SP4(0@192.168.3.61:5083)
09:29:59 Ringing (PH1)
09:29:59 Call Failed (404 Not Found; SP4(0@192.168.3.61:5083))
09:30:06 Call Connected (PH1)
09:56:03 Call Ended
I tested this config a few times and get the same error message. There are no blocked ports or IPs within the internal network.
A port scan of the OBI202 shows that 3 ports are open:
53: domain
80: http
18000: Beckman Instruments Inc.
azrobert:
I have the same setup (routing line calls to another device) except I'm using an OBi110 and an OBi200. I tried to reproduce your problem and couldn't get a 404 error. Your devices have the same subnet. Are you running them in bridge mode? I don't own an OBi2x2 and not familiar with all the settings, so you might need to get someone else to help.
You can get it to work over the OBiTalk network until you fix this.
## OBI212 Config
Physical Interfaces>LINE Port
InboundCallRoute: ph,pp(510111111)
Replace 510111111 with the OBi number of the OBi202
## OBI202 Config
Voice Services>OBiTalk Service
InboundCallRoute: ph
This is the default, but the setup process might add code to send calls to the Auto Attendant.
Navigation
[0] Message Index
[#] Next page
[*] Previous page