Routing li1 Calls Between obi212 and obi202 Devices
dboling:
Quote from: azrobert on August 27, 2018, 09:05:22 am
OBi212 Line InboundCallRoute: ph,sp4(0@xx.xx.xx.xx:pppp)
xx.xx.xx.xx = IP address of OBi202
pppp = X_UserAgentPort of OBi202 SP4 Service
ITSP Profile D SIP
X_SpoofCallerID: Checked
Needed to pass CallerID
OBi202
ITSP Profile D SIP
X_DiscoverPublicAddress: Unchecked
I was able to get this to work with sp4(0@xx.xx.xx.xx:pppp)
On the OBI202 I need to go to Voice Services>SP4 Service>X_EnforceRequestUserID and UnCheck it.
There is a bug on the OBI212 that causes it not to release the Line Port. I'm going to start a new topic in firmware regarding the bug.
azrobert:
Quote from: dboling on September 17, 2018, 09:08:28 am
I was able to get this to work with sp4(0@xx.xx.xx.xx:pppp)
On the OBI202 I need to go to Voice Services>SP4 Service>X_EnforceRequestUserID and UnCheck it.
The default is unchecked, so why was it checked? Did you use a wizard to define CC and it checked the setting?
Outbound OBi202 calls can be routed to Line. I can show you how if you're interested. I'm doing this on my OBi200/OBi110 and use a "9" prefix to identify these calls.
dboling:
I used the OBItalk web interface. The plan was to get it setup then dump the web interface. it was checked on both the OBI202 and OBI212.
I just posted at http://www.obitalk.com/forum/index.php?topic=14971.0 with the issue I'm having.
dboling:
Quote from: azrobert on September 17, 2018, 10:14:28 am
Quote from: dboling on September 17, 2018, 09:08:28 am
I was able to get this to work with sp4(0@xx.xx.xx.xx:pppp)
On the OBI202 I need to go to Voice Services>SP4 Service>X_EnforceRequestUserID and UnCheck it.
Outbound OBi202 calls can be routed to Line. I can show you how if you're interested. I'm doing this on my OBi200/OBi110 and use a "9" prefix to identify these calls.
Yes, I'd like to set it up for when the internet in down, so I can dial 911 from the obi202 to the obi212 Line Port.
I only have incoming calls and 911 service on the Verizon landline.
Since nobody on this forum has any ideas what the issue is with my OBi212 I decided it must be defective and called Amazon for a replacement. It should be here in a few days.
azrobert:
Quote from: dboling on September 18, 2018, 06:01:27 am
Yes, I'd like to set it up for when the internet in down, so I can dial 911 from the obi202 to the obi212 Line Port.
OBi202
Voice Services -> Gateways and Trunk Groups -> Voice Gateway 1
Name: OBi212
Access Number: sp4(xx.xx.xx.xx:pppp)
DigitMap: (911)
AuthUserID: dboling
xx.xx.xx.xx = IP address of OBi212
pppp = X_UserAgentPort of OBi212 SP4 Service
Physical Interfaces -> Phone1/2 Port
Add following to the beginning of the OutboundCallRoute:
{(Mvg1):vg1},
OBi212
ITSP Profile D SIP
X_DiscoverPublicAddress: Unchecked
SP4 Service -> X_InboundCallRoute:
{dboling>911:li},{ph}
Navigation
[0] Message Index
[#] Next page
[*] Previous page