outbound call route to different SP

(1/2) > >>

feld1234:
Hi all,

I'm new here, so i need some help. I bought a OBI2182 to use as an office phone with my GV # as the office number. I routed GV to Callcentric to be able to get CNAM. I also have a 3rd SP for international (localphone).

I set it up as follows:
SP1 as GV
SP2 as CC
SP3 as LocalPhone
incoming calls only ring from SP2


Now I would like to to know how to set it as follows:
1) All national (USA) calls to dial out from SP1 (GV)
2) International calls to 0119725 from SP2 (if international was dialed using the universal international code (00) replace 00 with 011), automatically add #after 15 digits
3) All other international calls from SP3 remove 00 or 011 from beginning of number, & add # after no digit was pressed for 5 seconds

I tried setting a user defined DigitMap label as nat, then set digitmap as (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.), then adding the first thing in outboundCallRoute {(Mnat):sp1} but it didn't seem to help.

Thanks in advance

drgeoff:
http://www.obitalk.com/forum/index.php?action=dlattach;topic=9104.0;attach=878

feld1234:
Quote from: drgeoff on February 25, 2019, 04:12:29 pm

http://www.obitalk.com/forum/index.php?action=dlattach;topic=9104.0;attach=878


Thanks for your reply, I already read thru this whole booklet yesterday, but I just can't seem to figure out how to imple the it. As much as itried it didn't work.

azrobert:
The following assumes SP1 is your Primary Line.

ITSP A DigitMap: (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx)

ITSP B DigitMap: (0119725xxxxxxxx<#>)

ITSP C DigitMap: (011xx.<#>)

User Defined Digit Map2
Label: intl
DigitMap: (0119725xxxxxxxx|<00:011>9725xxxxxxxx|011xx.S5|<00:011>xx.S5)

Add (Mintl)| to the IP Phone DigitMap after the beginning parenthesis.

Add following to the beginning of the IP Phone OutboundCallRoute
{(Msp2):sp2},{(Msp3):sp3},

If you want, I'll provide an explanation tomorrow. (I'm assuming the above will work)

feld1234:
Quote from: azrobert on February 25, 2019, 10:10:13 pm

The following assumes SP1 is your Primary Line.

ITSP A DigitMap: (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx)

ITSP B DigitMap: (0119725xxxxxxxx<#>)

ITSP C DigitMap: (011xx.<#>)

User Defined Digit Map2
Label: intl
DigitMap: (0119725xxxxxxxx|<00:011>9725xxxxxxxx|011xx.S5|<00:011>xx.S5)

Add (Mintl)| to the IP Phone DigitMap after the beginning parenthesis.

Add following to the beginning of the IP Phone OutboundCallRoute
{(Msp2):sp2},{(Msp3):sp3},

If you want, I'll provide an explanation tomorrow. (I'm assuming the above will work)



Will definitely give it a try.

Yes primary line is SP1, but would also want that even when I press the button (right key) assigned to sp2, it should still follow all rules and dial via the rule assigned by the digit map
Where exactly do I add (Mintl)|? After first parenthesis?
Also I don't seem to see where all intl calls except 0119725 are routed to Sp3? (Could be it's there, I just dont read it correctly).

Navigation

[0] Message Index

[#] Next page