Setup OutboundCallRoute with a pots line and Google Voice for day to day use
tbaggott:
Hi, I looking to change my DigitMap to automatically switch from my pots line to GV when calling out side of my calling area. Right now I have the DigitMap set as (1xxxxxxxxxx|<1540>xxxxxxx|011xx.|xx.) in the ITSP Profile A. Any time I call a 540-xxx-xxxx that is not in my local area, I get, that I do not have a long distance carrier. What I want is this, all 540 numbers except 852, 237, 515, 828, 896, 901, 879, 833, 298, 713, 249, 208, 209, 236, 432, 433, 434, 437, 438, 442, 564, 568, 574, 612, 615. 689, 705, 712, 801, 908, 867, 269,289, 234, 453. Go to GV and any other area codes automatically. Pots line is my primary. And I assume I do it in the ITSP Profile A. I'm new at this so make it simple as you can, if possible.
Thank you for any help, tbaggott :)
Northern.Bob:
I had a similar problem. I wanted my two local area codes (514, 450) plus 911, 310 numbers, 411, and 611 to go out my POTs line and all else out Google Voice. Below is how I modified the "Phone Port" pages OutboundCallRoute:
{(<#:>|911|<1514:514>xxx xxxx|<1450:450>xxx xxxx|310xxxx|411|611):li},{**0:aa},{***:aa2},{(Mpli):pli},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp}
The modified area is in red. In my setup the OBi unit was, for some reason, automatically prepending a 1 to the number dialed so the code <1514:514>xxx xxxx|<1450:450xxx xxx> is there to strip out the 1. The above modified code plus setting the Primary Line to SP2 (Google Voice) did it for me. Anything not listed in the above code goes out through GV.
QBZappy:
Note this rule:
!1xxx xxx xxxx – Barring all 11-digit numbers
Digimaps:
1) Phone line Port:
I assume you want to pass only area code 540 on Pots and block everything else on this line. This keeps it simple. Note the "!" bars numbers. Place the bar everything first, then allow "540". Obi reads digimaps from left to right. I think this should work.
example:
(!1xxx xxx xxxx|<1540>xxxxxxx)
2) GV (SP!):
Insert this into your GV digimap. Don't forget the "|" pipe separator character. Does it matter if 540 goes through GV, it is a free call, other that having local CID to the receivers phone.
!1540|
3) Phone OutboundCallRoute:
{(!1xxx xxx xxxx|x.540xxxxxxx|):li},{(!x.540 xxx xxxx|1xxxxxxxxxx|011xx.|xx.):sp1},
There are other ways to do this I'm sure. Maybe someone else can have a shot at it.
tbaggott:
Hi, Would this work in the "Phone Port" pages OutboundCallRoute, without changing the primary from PSTN
{(<#:>|911|<1540:540>xxxxxxx|208xxxx|209xxxx|234xxxx|236xxxx|237xxxx|249xxxx|269xxxx|289xxxx|298xxxx|432xxxx|433xxxx|134xxxx|437xxxx|438xxxx|442xxxx|453xxxx|515xxxx|564xxxx|568xxxx|574xxxx|612xxxx|615xxxx|689xxxx|705xxxx|712xxxx|713xxxx|801xxxx|828xxxx|833xxxx|852xxxx|867xxxx|879xxxx|896xxxx|901xxxx|908xxxx|411):li},{**0:aa},{***:aa2},{(Mpli):pli},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp}
Thanks, tbaggott
tbaggott:
Hi, Also if I have to make my Primary Line to SP1 (Google Voice) how do I do that.
thanks, tbaggott
Navigation
[0] Message Index
[#] Next page