Obi200 UK Google Voice
Jake100:
Hi,
I have been trying for hours to get this working properly and I am running out of ideas.
I have a Gsuite account with a UK number.
I can receive incoming calls through my Obi device but I cannot make outgoing calls without dialling the 011 US international prefix. If I dial 011447xxxxxxxxx it works fine. But if I dial 07xxxxxxxxx (UK mobile number) then an automated message says "This is not a valid number".
I have Google Voice configured using SP1.
I have tried various DigitMaps from this forum as well as the one from the Obi guide but none of them work for dialling without the 011 prefix.
(999|112|101|111|116000|116111|116123|1471|1571|0[15]xxxxxxxxx?|0[27]x xxxx xxxx|0800xxx xxxx?|0808xxx xxxx|08001111|08[47]x xxx xxxx|0845464x|03xx xxx xxxx|118xxx|100|155|195|09xx xxx xxxx|00xxx.|xx.|+xx.|(Mipd)|[^*#]@@.)
This is one of the example ones I tried. I'm quite happy with a simple DigitMap.
Is this 011 prefix listed in the settings somewhere else which I need to remove?
I have exported my current XML and searched for 011 but nothing of interest comes up.
Does anyone have any other ideas as to what's stopping me dialling UK numbers without the US international prefix?
Thanks!
SteveInWA:
The OBi 200 is not supported for use with Google Voice for G Suite, so I would not expect it to work, assuming you mean you are paying for the new G Suite version of GV.
The only approved VoIP hardware for G Suite are the Poly VVX x50 IP phones.
Jake100:
Hi Steve.
Thanks for the quick reply.
Yes I am using the new GSuite and I have seen it isn’t officially supported.
However, I can make and receive calls fine so it does work after a fashion.
The only problem I’m having is how I make outgoing calls.
I currently have to use the 011 US international prefix to make outgoing calls. I was hoping someone may know how to fix this bit which will allow me to dial UK numbers like I would normally from within the UK.
If I log into my google voice account, I can see the history of numbers being dialled.
They are being dialled with a +1 in front of them.
E.g I dial 07xxxxxxxxx on the phone.
The number which gets dialled through Google Voice is +107xxxxxxxxx
I realise it’s not officially supported and it may stop working completely at some point. But I feel it is promising the fact I can dial in and out, it just needs some tweaks to my config somewhere.
drgeoff:
First check what your OBi is sending to GV. Point a browser at the 200's IP address on your LAN and log in with admin and admin or whatever if you changed the password. Click on Status and then on Call History.
Are you sure your Digit Map changes are sticking? You will have used the obitalk.com portal to configure for GV. Unless you have disabled Obitalk Provisioning you should modify digit maps etc using Expert Mode on the portal. Otherwise changes you make using the onboard web server will be overwritten by the portal.
Jake100:
Hi drgeoff.
Thanks for the reply.
I have started using expert mode and things are looking more promising but still not quite there unfortunately, I still get the number not valid message.
If I dial 0774xxxx362 and look at the active call, Obi displays the correct number (please see attached).
When I look in Google Voice, it has dialed the first 10 digits but the last digit isn't showing in GV; it has only dialed 0774xxxx36.
I even tried a very simple digitMap like the one below. I believe dialing 07.... should match the first rule and dial the 11 digits through sp1.
(0xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1aaa>xxxxxxx|011xx.|(Mipd)|[^*]@@.'@'@@.)
I appreciate everyone's help :)
Navigation
[0] Message Index
[#] Next page