Outbound Call Route help

(1/2) > >>

sviv:
Hi there,

I have been reading through forum posts and manuals and can't find a solution to my problem.

My set up is OBi200:

sp1 = voip.ms SIP = Canadian number:
digit map:
(*xx|1xxxxxxxxxx|<1519>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)

sp2 = GV outgoing calls only, no number assigned
digit map:
(!911|*xx|<+>1xxxxxxxxxx|<+1519>[2-9]xxxxxx|<+1>[2-9]xxxxxxxxx|<011:+>xx.|(Mipd)|[^*]@@.)

sp3 = zadarma SIP = local land line number in Poland country code = 48, area code = 22 plus 7 digit local phone number
digit map:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)

Physical Interface PHONE 1:

digit map:
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))

OutboundCallRoute:
{911:sp1},{933:sp1},{([1-9]x?*(Mpli)):pp},{(<##:>):li},{(<**70:>(Mli)):li},{(<**82:>(Mbt2)):bt2},{(<**81:>(Mbt)):bt},{(<**8:>(Mbt)):bt},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Msp3)):sp3},{(<**4:>(Msp4)):sp4},{(<**9:>(Mpp)):pp},{(Mpli):pli}

I just got zadarma service couple days ago and I can receive inbound calls, however, I cannot dial out from sp3.  When I use **3 and dial 9 digit number in Poland I get "Call Ended (400 Content-Length mis-match)" error.  Same problem when dialing 00 1 and 10 digit NA phone number.

I have no idea why this is happening, I am out of ideas what to try.  If anyone can help me that would be great.

What I would like to eventually achieve is to be able to use sp3 whenever I dial 011 48 (without dialing **3) which I was able to successfully test by using {(01148xx.):SP3} in the OutboundCallRoute.  I could see in the logs that the call was routed through sp3, but not completed due to the above described problem.

All other outbound calls I would like to route through sp2 (I have checked box in sp2 for Primary Line for Outgoing Calls Phone 1.

Thank you in advance for your input!

zapattack:
When you dial using **3, does your call history
show 48 22 xxxxxxx being sent on SP3?
See Zadarma support IP Telephony/Dialing Format for more info.

sviv:
Quote from: zapattack on December 22, 2020, 11:29:08 pm

When you dial using **3, does your call history
show 48 22 xxxxxxx being sent on SP3?
See Zadarma support IP Telephony/Dialing Format for more info.

Yes it does show going to sp3 in the history.

I think you are right about Zadarma dialing format may be an issue. I checked and it says that I need to dial country code which I was not doing.  If dialing the country code is a requirement is my digit map okay or would it have to be changed?

azrobert:
Try the following. The “+” is not required for GV and can cause problems.

sp1 = voip.ms SIP = Canadian number:
digit map: no change

sp2 = GV outgoing calls only, no number assigned
digit map:
(*xx|xxxxxxxxxx|<1519>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx)

sp3 = zadarma SIP = local land line number in Poland country code = 48, area code = 22 plus 7 digit local phone number
digit map:
(<011>48xxxxxxxxx|01148xxxxxxxxx)

Physical Interface PHONE 1:

digit map:
(48xxxxxxxxx|[1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))

OutboundCallRoute:
{911:sp1},{933:sp1},{(Msp3):sp3},{([1-9]x?*(Mpli)):pp},{(<##:>):li},{(<**70:>(Mli)):li},{(<**82:>(Mbt2)):bt2},{(<**81:>(Mbt)):bt},{(<**8:>(Mbt)):bt},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Msp3)):sp3},{(<**4:>(Msp4)):sp4},{(<**9:>(Mpp)):pp},{(Mpli):pli}

Now dial “48xxxxxxxxx”, no “011”

Edit
Make sure you include my edits

sviv:
azrobert,

thank you very much for your input.

I updated all the settings with the edits you have provided.  Dialing from sp3 via **3 still didn't work so I tried something else.
Your suggestion was to do  this for sp3 digit map:

(<011>48xxxxxxxxx|01148xxxxxxxxx)

Based on what I had read on Zadarma website I tried below and it worked:

(<+>48xxxxxxxxx|+48xxxxxxxxx)

So current situation is as follows:

sp2 - GV is default primary line to dial out
sp1 - voip.ms works when selected by **1
sp3 - Zadarma is selected automatically when I dial 48 xxx xxx xxx - this is awesome! Thank you very much for your help!

If you don't mind, I have one more question.  What would I need to add or edit to have calls in area code 226 and 519 automatically routed through sp1?  I would be ok if these calls went through sp2 - GV but when dialed from GV the call display shows "unknown".  I would prefer to have my home phone number displayed on caller ID within local calling area.

Again, thank you for your help.

Navigation

[0] Message Index

[#] Next page