Problem getting IP<>PSTN to work

<< < (3/4) > >>

azrobert:
A config example:

OBi212

Service Providers -> ITSP Profile D SIP -> ProxyServer: 127.0.0.1
Service Providers -> ITSP Profile D SIP -> X_SpoofCallerID: Checked
Service Providers -> ITSP Profile D SIP -> X_Proxy: Unchecked
Voice Services -> SP4 Service -> X_ServProvProfile: D
Voice Services -> SP4 Service -> AuthUserName: GXP1610
Voice Services -> SP4 Service -> X_RegisterEnable: (unchecked)
Voice Services -> SP4 Service -> X_InboundCallRoute:
{GXP1610>(Msp1):sp1}

Physical Interfaces -> Line Port-> InboundCallRoute:
ph,sp4(GXP1610@yy.yy.yy.yy:pppp)

Replace yy.yy.yy.yy:pppp with the IP address and port of the GXP1610

IP Phone:
Proxy: 192.168.1.100  (IP address of the OBi212)
Proxy Port: 5063     (X_UserAgentPort of OBi212 SP4 trunk)
UserID: GXP1610
Password: anything

Gillburt:
Quote from: azrobert on February 03, 2021, 11:03:39 am

A config example:

OBi212

Service Providers -> ITSP Profile D SIP -> ProxyServer: 127.0.0.1
Service Providers -> ITSP Profile D SIP -> X_SpoofCallerID: Checked
Service Providers -> ITSP Profile D SIP -> X_Proxy: Unchecked
Voice Services -> SP4 Service -> X_ServProvProfile: D
Voice Services -> SP4 Service -> AuthUserName: GXP1610
Voice Services -> SP4 Service -> X_RegisterEnable: (unchecked)
Voice Services -> SP4 Service -> X_InboundCallRoute:
{GXP1610>(Msp1):sp1}

Physical Interfaces -> Line Port-> InboundCallRoute:
ph,sp4(GXP1610@yy.yy.yy.yy:pppp)

Replace yy.yy.yy.yy:pppp with the IP address and port of the GXP1610

IP Phone:
Proxy: 192.168.1.100  (IP address of the OBi212)
Proxy Port: 5063     (X_UserAgentPort of OBi212 SP4 trunk)
UserID: GXP1610
Password: anything



Brilliant - thank you, that was exactly what I needed to mentally join the dots.
Incoming calls are now working.

Hopefully outgoing won't be too difficult to work out.

 ;D ;D

Gillburt:
Ha, famous last words.
Cannot get outbound call to work.

I get a 404 not found message on the phone.
What config information do I need to post on here to help ?

drgeoff:
Quote from: Gillburt on February 07, 2021, 11:06:26 am

Ha, famous last words.
Cannot get outbound call to work.

I get a 404 not found message on the phone.
What config information do I need to post on here to help ?

The example that azrobert gave you is for making calls using the 212's SP1, not its LINE port.

Try changing

{GXP1610>(Msp1):sp1}

to

{GXP1610>(Mli):li}

RonLynnwood:
Hi everyone!  Just also wanted to chime in about what a PoS the registration is, can't get my device added either.

Also, go to "FAQ", then "Troubleshooting", then "Add Device does not work when doing **5 during OBiTALK set-up."

This says

Quote

Add Device does not work when doing **5 during OBiTALK set-up.
Please follow the Self-Troubleshooting Guide: http://www.obihai.com/support/troubleshooting/trs1-3


Go to that link.  Some excellent advice there!    ;D

Quote

if that Add Device page remained the same, does not change within the span of 180-Secs countdown, with pop-message remained, please re-input the same code again (**5 1234) after 10-Secs to 15-Secs.

If the first 10-Secs to 15-Secs round and page remained, please repeat the same code **5 1234. If that 180-Secs countdown ends with Add Device page unchanged, please wait up to 2-minutes and try Add Device again.


Hmm, speaka da English?  Apparently not.  What is this BS trying to say.  Who knows, probably makes no difference.

Navigation

[0] Message Index

[#] Next page

[*] Previous page