Set-up For International Usage

[larrybob]

I could not find a complete list of which changes are needed for Using OBi outside the U.S.  I am setting up for use in Brazil. Below, are all the parameters I changed, in the order they appear on the OBiTALK Expert interface.

I changed the RingProfile and ToneProfile B so I could use the default Profile A with Google Voice on SP1. I believe the ring and tone profile could be left unchanged and all would function properly. Changing the profiles duplicates the experience a caller would have using a PTSN line in the country of use. If I add other changes, I will add to this post.
The important Setting here in addition to the Digitmap and CallRoute, is the DisconnectTone Pattern. If this is not correct, and is used by the phone system you are interfacing with, the call might not be recognized as finished , when the call is ended.
Larry

CHANGES FOR INTERNATIONAL USAGE ( Example-BRAZIL)
PHONE PORT
   DigitMAP               (Details not Shown Here)
   OutBoundCallRoute         (Details not Shown Here)   
   PrimaryLine             PSTN Line
   Tone Profile             B
   
LINE PORT:
   RingProfile               B
   ToneProfile               B
   DisconnectTone Pattern         425-30,425-30;10;(.25+.25)
TONE PROFLIE B:
   Dial Tone                  425-18,425-18,450-18;20
   Second Dial Tone (U.S.)            350-18,440-18;20
   Ringback tone               425-18;-1;(1+4)
   Busy Tone                  425-18;10;(.25+.25)
   Reorder (Congestion)            425-18;10;(.75+.25,.25+.25)
   Confirmation (Function Acknowlege)   425-18;1;(.1+.1,.1+2)
RING PROFILE B            
   Call Waiting Tone 1            425-18;30;(.05+1)
   Ring Pattern 1               60;(1+4,1+4)


Here is a link for a list of tones in various countries:
http://www.hackcanada.com/blackcrawl/telecom/tones.txt

[PhASE]

how we can apply tis information using obihai setting page !?
for example am in saudi arabia
i did find this :
Saudi Arabia (Kingdom of)
   Busy tone -   425   0.5 on 0.5 off
   Congestion tone -   425   0.25 on 0.25 off
   Conference tone -   425   0.5 on 2.0 off 0.5 on 15.0 off
   Dial tone -   425   continuous
        Payphone recognition tone -     1600/1200       0.2 on 0.2 off
                                                        0.2 on 4.0 off
   Ringing tone -   425   1.2 on 4.6 off
   Call waiting tone -   425   0.15 on 0.2 off 0.15 on 10.0 off
==========================================
exactly what changes i have to do in my obi110 !?
regards

[jimates]

Enter the Obi Expert Configuration and make the changes to the
Tone Settings -> Tone Profile A or B and to the Ring Settings -> Ring Profile A or B

Profile A or B corresponds to the ITSP Profile A or B so make the changes to the profile that your service is using.

Physical Interfaces -> Phone -> Calling Features -> Tone Profile = (default is A, or you can use profile B)
make your changes to the appropriate (A or B) Tone Settings -> Tone Profile

Voice Service -> SPx Service -> X_RingProfile = (default is A, or you can use profile B)
  SPx indicates the SP service for the provider you are wanting to make changes on.
Make your changes to the appropriate (A or B) Ring Settings -> Ring Profile

You must remove the check from both boxes on the right before you can make any changes.

[RonR]

Tone Settings -> Tone Profile A or B and to the Ring Settings -> Ring Profile A or B

Profile A or B corresponds to the ITSP Profile A or B so make the changes to the profile that your service is using.

Tone Profile is associated only with the PHONE Port (not ITSP Profile A or B) and defaults to A (Tone Profile B is not used anywhere by default).

Ring Profile is associated only with the SPx Service (not ITSP Profile A or B) and defaults to A (Ring Profile B is not used anywhere by default).

[PhASE]

Dear RnoR
the setup interface is not user friendly at all !!
i have to change & modify every single detail manually !!
even if i need to make forward calls , change ring tone, any thing must programmed by user,
programmed not just entered
there are no values are easy to changed
no drop menu  is easy to use
i have to read the forum & to try to program my obi !!!
i think you agree with me that it is time consuming !!

[MichiganTelephone]

how we can apply tis information using obihai setting page !?
for example am in saudi arabia
i did find this :
Saudi Arabia (Kingdom of)

Here are the main ones:

   Busy tone -   425   0.5 on 0.5 off
425-18;10;(.5+.5)

   Congestion tone -   425   0.25 on 0.25 off
425-18;10;(.25+.25)

   Dial tone -   425   continuous
425-18;20

    Ringing tone -   425   1.2 on 4.6 off
425-18;-1;(1.2+4.6)