In bound callroute question. Bridging incoming calls to home number.
larrybob:
I'll do a factory reset, and try to duplicate your results, and also see if *72 begins to function. I will post the results here. Larry
larrybob:
I did a factory reset, and the *72 still is not functioning at all( Just get a high pitched tone.)
IT DID FIX THE BRIDGING PROBLEM However:: NOW IT WORKS!.RULE :{sp1(14154871880)}
here is the call record:
Terminal ID GoogleVoice1 GoogleVoice1
Peer Name
Peer Number 14159944804 14154871880
Direction Inbound Outbound
23:18:53 Ringing
23:19:06 Call Connected
23:19:07 End Call
WHEN I CHANGE TO SP2 ALSO WORKS AS IT SHOULD. RULE :{sp2(14154871880)}
Terminal ID GoogleVoice1 SP2
Peer Name
Peer Number 14159944804 14154871880
Direction Inbound Outbound
23:15:36 Ringing
23:15:42 End Call
THANKS RON!
The actual rule I will be using is :{sp2(558585263264)}
(All Calls coming into my google voice number will bridge automatically to the specific number above in Brazil)
Which digit map is used when I do this? Is it ISTP Profile B?
the Default map on ITSP Profile B is :
(1xxxxxxxxxx|<1415>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)
If I am making calls to brazil ,will this change speed up the call?
(55xxxxxxxxxx|1xxxxxxxxxx|<1415>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)
Thanks Larry
RonR:
Quote from: larrybob on December 27, 2011, 11:35:01 pm
I did a factory reset, and the *72 still is not functioning at all( Just get a high pitched tone.)
After dialing *72, you will get a prompt tone to enter the desired forwarding number followed by the # key. The number you input will be run through the appropriate DigitMap for validation and possible transformation. The result will set all trunk CallForwardUnconditionalNumber fields using TK format. No DigitMap or OutboundCallRoute will be used when numbers in TK format are sent to the appropriate trunk.
Also, be aware that all InboundCallRoute rules on all trunks will be ignored while *72 is in effect.
larrybob:
Thanks, i was expecting a voice prompt, not a tone for the forwarding.. all is working !
My question is why are things are working? and about the inbound call routing, from sp1, bridging the call out to sp2.
I am not sure if the digit maps work the same as from the phone. If entering a number that only matches xx., this is an indefinitely matched value. Will the long timer be put into play?
I am guessing the digitmap used for sending calls to SP2 is ITSPB.
I changed the original rule by adding what is in bold. (55 and 10 digits)
the Default map on ITSP Profile B is :
(55xxxxxxxxxx|1xxxxxxxxxx|<1415>[2-9]xxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)My change was actually never implemented.. I think I forgot to click the update button.
Note: After looking again, calls to Brazil would also have matched <1>[2-9]xxxxxxxxx. The calls went through before I added the 55 rule... if that rule was not there, I think 1 would have been added to my number, which would have prevented the call from going through. Would not have matched, the number to call to Brazil has 12 digits, not the 10 digits in the rule.
So.... I am not sure what is going on.... and why things worked with the original rule? it seems the problem would not have been the long timer kicking in, but 1 being appended to the number??
Problem is the long timer.. see later posts.. Larry
Larry
RJDB:
I tried a simple *72 to forward from the Line Port to SP1(xxxxxxxxxx).
I also did not receive the expected voice prompt - but the tone. I entered **1 xxxxxxxxx followed by #. I received the confirmation tone.
Voice Services - OBiTalkService - Calling Features reflected the proper CallForwardUnconditional parameters.
Physical Service - Line Port - Calling Features also reflected the proper CallForwardUncondidtional parameters.
The call forward worked. However, I do not understand why the voice prompt on the *72 did not work.
UPDATE - Just revisited the Administrator Guide.
Under Call Forwarding, it states:
"...To enable Call Forward ALL, from a phone attached to the OBi, dial *72. You will be prompted to enter the number to which the calls will be forwarded. Dial the number plus the # key and a confirmation tone will be heard."
I interpretted "prompted" to mean a voice prompt.
In the following Tone & Ring Patterns section of the Admin Guide, it states:
Prompt Tone:
PROMPT, "480-16;10"
Prompt tone is generated from a single frequency component:
480 Hz at -16 dBm. The expiration time is exactly 10 seconds. It has only one cadence segment, which has tone infinite active time.
Navigation
[0] Message Index
[#] Next page
[*] Previous page