Outbound CID Spoofing is it possible?
VaHam:
Quote from: RonR on April 08, 2011, 02:01:32 pm
From page 58/59 of the latest version of the OBi Device Administration Guide:
Allow outbound Caller ID spoofing. If set to Yes, device will attempt to set the caller-id name and userid field in the FROM header to that of a remote caller in the case of a bridged call (from another trunk, such as PSTN Line or another SP Service). Otherwise, device always its own account information to form the FROM header.
Note that most service provider will not allow originating a call if the FROM header field does not match the account credentials. Enable this option only if you are sure that the service provider allows it. For example, an IP PBX may allow it.
X_SpoofCallerID is simply an enable checkbox. It applies to bridged calls (a call originated by the OBi that is then connected to an incoming call). If X_SpoofCallerID is disabled (default), the OBi will use your CallerID info when originating the outgoing call. If X_SpoofCallerID is enabled (checked), the OBi will attempt to use the CallerID info from the incoming call that it intends to bridge with.
Yes I read the document but this still provides no example of how to use it as I described. The source is the attached phone not from an incoming call; and I do not see any example of defining spoofed cid.
I am guessing it is done by modifying the OutboundCallRoute of the Phone port in it's dial string but there is no example of the syntax anywhere that I can find. There are examples of w/o spoofing but none with.
Again I assume it is the {(<**2:>(Msp2)):sp2} rule which needs to be modified just not sure of the cid syntax needed here.
VaHam:
Well at least I don't feel so stupid! Apparently no one else knows how to do this either!
lhm.:
Some work around ways.
Change your VSP username/clientid to your GV#.
Voip.ms provides true spoofing for PSTN out. (ie:Send from the White House# cname shows United States. :o
Use listyourself.net.
Edit: To set in Voip.ms > Account settings> General> CallerID Number.
QBZappy:
VaHam
Quote from: VaHam on April 08, 2011, 09:37:04 pm
Quote from: RonR on April 08, 2011, 02:01:32 pm
X_SpoofCallerID is simply an enable checkbox. It applies to bridged calls (a call originated by the OBi that is then connected to an incoming call). If X_SpoofCallerID is disabled (default), the OBi will use your CallerID info when originating the outgoing call. If X_SpoofCallerID is enabled (checked), the OBi will attempt to use the CallerID info from the incoming call that it intends to bridge with.
Yes I read the document but this still provides no example of how to use it as I described. The source is the attached phone not from an incoming call; and I do not see any example of defining spoofed cid.
I am guessing it is done by modifying the OutboundCallRoute of the Phone port in it's dial string but there is no example of the syntax anywhere that I can find. There are examples of w/o spoofing but none with.
Again I assume it is the {(<**2:>(Msp2)):sp2} rule which needs to be modified just not sure of the cid syntax needed here.
CID Spoofing does not belong in the digi mapping. There is no CID syntax. The only place in the OBi you can type in some type of CID is in the
Voice Services>SP1 (2) Service>Calling Features>Parameter Name>CallerIDName = Whatever
See if that works.
I use VoipMS. Their CID spoofing works by getting the CID you setup in the ATA or PBX account when it registers with their service.
VaHam:
Quote from: QBZappy on April 11, 2011, 02:14:48 pm
CID Spoofing does not belong in the digi mapping. There is no CID syntax. The only place in the OBi you can type in some type of CID is in the
Voice Services>SP1 (2) Service>Calling Features>Parameter Name>CallerIDName = Whatever
See if that works.
I use VoipMS. Their CID spoofing works by getting the CID you setup in the ATA or PBX account when it registers with their service.
No I have tried CallerIDName and that doesn't work to change the cid.
Page 115/116 talks about cid spoofing in the OutboundCallRoute. It shows cid as an arg of the terminal and says it is a literal string. That is what is confusing me. I know cid spoofing works with my provider because using the same account from my Asterisk box spoofs it just fine. But I have tried many different combinations of syntax as described on page 115/116 of the latest Obi User Guide to no avail.
Navigation
[0] Message Index
[#] Next page
[*] Previous page