Two Obi's - Remote Users - Same GV Acct Inbound/Outbound
RonR:
Give me a few minutes and I'll see what I can come up with...
RonR:
The following assumes Google Voice is configured and working on SP1/ITSPA, Voip.ms is configured and working on SP2/ITSPB, the LINE Port is not used, and 911 calls are to be routed to SP2.
Service Providers -> ITSP Profile A - General -> DigitMap : (Mste)
Service Providers -> ITSP Profile B - General -> DigitMap : (Mste)
Voice Services -> SP1 Service -> X_InboundCallRoute : {pp(ob290123456),ph}
Voice Services -> SP2 Service -> X_InboundCallRoute : {pp(ob290123456),ph}
Voice Services -> OBiTALK Service -> InboundCallRoute:
{290123456>911:sp2},{290123456>(Mtg1):tg1},{290123456:aa},{pp(ob290123456),ph}
where 290123456 is the OBiTALK number of your OBiON App.
Voice Services -> Gateways and Trunk Groups -> Trunk Group1
Name : Primary Line
TrunkList : sp1,sp2
DigitMap : (Mste)
Physical Interfaces -> PHONE Port -> OutboundCallRoute:
{([1-9]x?*(Mpli)):pp},{(<#:>):li},{911:sp2},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},
{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Physical Interfaces -> PHONE Port -> PrimaryLine : Trunk Group 1
User Settings -> User Defined DigitMaps -> User Defined Digit Map2
Label : ste
DigitMap : (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1aaa>[2-9]xxxxxx|011xx.|(Mipd)|[^*#]@@.'@'@@.)
where aaa is your local area code.
All incoming calls will ring the PHONE Port and the OBiON App.
Outgoing calls will use SP1 if available, otherwise SP2.
Joshinforum:
That looks good. I'll let you know if I have any problems with it. One more question. Is there any way that if sp1 was full (in/in , out/out, or in/out) that the calls would automatically roll to sp2 from within the obi? I don't think it's possible to setup a hunt type group with GV and forwarding calls from sp1 to sp2 would make both lines ring at all times instead of only when sp1 was full.
Thanks for the config and hopefully I can find something to do with the additional obi.
RonR:
You could disable the Google Chat phone (uncheck the box on it) in your Google Voice account and have Google Voice ring your Voip.ms number. Outgoing Google Voice calls from the OBi will still work. This would make all incoming calls, from either your Google Voice number or your Voip.ms number come in on SP2, reserving SP1 for two outgoing calls. This may or may not buy you anything depending on Google Voice limitations as it's not clear whether the two session limit is in the OBi or Google Voice. If the limit is with Google Voice (likely) then this will probably interfere with using the Trunk Group as the OBi will probably try to put the call through to Google Voice where it will be rejected and the Trunk Group logic in the OBi will not try SP2 at that point. It might be worth a try, but don't get your hopes up.
Joshinforum:
Everything seems to work fine so far. I don't like the fact that the softphone user still has to pick and option "it rings and says press 1 to continue this call 2 for new call 3 for enter a call back #" ...before making a call... Anyway we can adjust this ? I just want it to dial the number through whatever line is available.
Navigation
[0] Message Index
[#] Next page
[*] Previous page