Using OBi and GV Outside the USA
Jiver:
Woah...talk about gibberish
so doing all that, I would be able to dial straight, to a local number in Canada using GV through my Obi in the US?
or i still have to put something in speed dial, but have no delay in dialing thereafter?
Is there any way I could convince to write the exact syntax I need for the inbound call route (and the rest perhaps unless I just need to put my Obi#)?
to dial from Obi-US (SP2 i guess, being the 2nd GV line) using Obi-CAN
and I guess Obi-CAN receiving calls from Obi-US (SP2), where SP2 does not ring at Obi-US (only in CAN), if you say its possible without Sipgate forwarding
I assume no configuration is needed for Obi-US, right?
RonR:
You simply configure both OBi's with:
Voice Services -> OBiTALK Service -> InboundCallRoute:
{(Mcot)>(Mpli):pli},{(Mcot)>(<*1:>(Msp1)):sp1},{(Mcot)>(<*2:>(Msp2)):sp2},{(Mcot)>(<*8:>(Mli)):li},
{(Mcot)>(<*9:>(Mpp)):pp},{(Mcot)>(<**1:>(Msp1)):sp1},{(Mcot)>(<**2:>(Msp2)):sp2},
{(Mcot)>(<**8:>(Mli)):li},{(Mcot)>(<**9:>(Mpp)):pp},{(Mcot):aa},{ph}
Note: Replace pli above (2 places) with the OBi's PHONE Port -> PrimaryLine trunk name (sp1,sp2,li,pp,tg1) as the OBi won't do it for you.
User Settings -> User Defined Digit Maps -> User Defined Digit MapX:
Label : cot
DigitMap : (200123456|200123457)
where 200123456 is the OBiTALK number for OBi #2 and 200123457 is the OBiTALK number for OBi #3.
Note: These are trusted caller OBiTALK numbers. This DigitMap should also contain the OBiTALK numbers of any OBiON Apps that are used.
In the PHONE Port and Auto Attendant DigitMap's, change [1-9]x?*(Mpli) to [1-9]x?*@@.
In the PHONE Port and Auto Attendant OutboundCallRoute's, change {([1-9]x?*(Mpli)):pp} to {([1-9]x?*@@.):pp}
Speed Dial #2 : PP(ob200123456)
Speed Dial #3 : PP(ob200123457)
where 200123456 is the OBiTALK number for OBi #2 and 200123457 is the OBiTALK number for OBi #3.
From either OBi, you make calls though the local OBi dialing normally:
18005551212 -> Local PrimaryLine
**1 18005551212 -> Local SP1 Service
**2 18005551212 -> Local SP2 Service
**8 18005551212 -> Local LINE Port
**9 200123456 -> Local OBiTALK Service
From OBi #3, you make calls through OBi #2 by dialing:
2*18005551212 -> OBi #2 PrimaryLine
2 **1 18005551212 -> OBi #2 SP1 Service
2 **2 18005551212 -> OBi #2 SP2 Service
2 **8 18005551212 -> OBi #2 LINE Port
2 **9 200123456 -> OBi #2 OBiTALK Service
From OBi #2, you make calls through OBi #3 by dialing:
3*18005551212 -> OBi #3 PrimaryLine
3 **1 18005551212 -> OBi #3 SP1 Service
3 **2 18005551212 -> OBi #3 SP2 Service
3 **8 18005551212 -> OBi #3 LINE Port
3 **9 200123456 -> OBi #3 OBiTALK Service
If you'd like the other OBi's phone to ring on incoming calls (no Sipgate or Google Voice forwarding required):
For the trunk(s) you wish to ring the other OBi:
Voice Services -> SP1 Service -> InboundCallRoute
Voice Services -> SP2 Service -> InboundCallRoute
Voice Services -> OBiTALK Service -> InboundCallRoute
Physical Interfaces -> LINE Port -> InboundCallRoute
change ph or {ph} to {ph,PP(ob290123456)}
where 290123456 is the OBiTALK number of the other OBi.
Jiver:
Wow, thank you very much. ;)
Just one last question, when you say change pli in 2 places...
do you mean like where it says "{(Mcot)>(Mpli):pli}...."
i should put in "{(Mcot)>(Msp1):sp1}...." right?
sp1 being my primary line on Obi-US
while Obi-CAN is dialing/receiving calls from Obi-US's sp2...
as far as dialing from Obi-CAN through Obi-US...do i need to have 1+areacode+number?
or can i just dial 2*5551234 if i already set up that sp2's default area code?
or even better...
any way of dialing without the speed dial? making it the primary outbound code for Obi-CAN?
RonR:
Quote from: Jiver on September 04, 2011, 08:29:33 pm
Just one last question, when you say change pli in 2 places...
do you mean like where it says "{(Mcot)>(Mpli):pli}...."
i should put in "{(Mcot)>(Msp1):sp1}...." right?
That's correct.
Quote from: Jiver on September 04, 2011, 08:29:33 pm
sp1 being my primary line on Obi-US
while Obi-CAN is dialing/receiving calls from Obi-US's sp2...
Each OBi needs to get the same changes described in this thread. Each OBi needs to have pli replaced with its respective PrimaryLine.
Jiver:
(if you missed before my edit)
as far as dialing from Obi-CAN through Obi-US...do i need to have 1+areacode+number?
or can i just dial 2*5551234 if i already set up sp2's default area code?
or even better...
any way of dialing without the speed dial? making it the primaryline for Obi-CAN?
Navigation
[0] Message Index
[#] Next page
[*] Previous page