Using obi with betamax
turuncu:
I am trying to setup new Obi device.
I would like to set it up so all local calls go through Google voice on SP1
911 goes through the land line (I think by default it is set up like that)
and all my international goes through betamax (when I dial 011xx it converts it to 00xx)
RonR helped with a previous setup and I though I would be ok on this one but it is not working out.
Here is my setup
Physical Iterfaces -> PHONE Port -> DigitMap:
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**8(Mli)|**9(Mpp)|(Mpli))
Physical Iterfaces -> PHONE Port -> OutboundCallRoute:
{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Service Providers -> ITSP Profile A -> General -> DigitMap:
(<1>[2-9]xxxxxxxxx|1xxxxxxxxxx|<**3>011xx.)
Gateways and Trunk Groups -> Voice Gateway3
Enable Yes
Name Poivy
Access number 77.72.169.131 When I tried SP2(SIP_Server_Proxy) I was getting a message from obi stating the account was not valid I don't understand the SP2
DigitMap : (<011:00>xx.|00xx.)
AuthUserID : My sip username
AuthPassword : My sip Password
With these settings I am getting a busy signal when I dial 011xxxx and the call log shows the following
Call 1 03/24/2012 20:37:37
Terminal ID PHONE1 OBiTALK1
Peer Name
Peer Number **3011902325648484 _g377.72.169.131*00902325648484
Direction Outbound Outbound
20:37:37 New Call
I am pretty sure that I have the correct login info for poivy. Is there a log file where it shows if it successfully logged on to the accounts.
Thanks for all the help
T
RonR:
Quote from: turuncu on March 24, 2012, 06:11:39 pm
Access number 77.72.169.131
The VG3 AccessNumber should be : SPx(sip.poivy.com)
SPx (SP1 or SP2) must be configured for SIP.
turuncu:
Quote from: RonR on March 24, 2012, 06:31:34 pm
Quote from: turuncu on March 24, 2012, 06:11:39 pm
Access number 77.72.169.131
The VG3 AccessNumber should be : SPx(sip.poivy.com)
SPx (SP1 or SP2) must be configured for SIP.
I though SP1 was google voice do I need to configure an additional SP on SP2?
I have tried SPx(sip.poivy.com), Sp1(sip.poivy.com) and SP2(sip.poivy.com) and all I get was obi announcment that says "there is no service available to complete your call" Thanks
RonR:
To use a Voice Gateway with a SIP provider, either SP1 or SP2 will have to be configured as SIP. Google Voice is not a SIP provider.
In an earlier post, you said you had Callcentric on SP2. If that's the case, the VG3 AccessNumber should be : SP2(sip.poivy.com)
What does the OBi Call History show for the failed call?
turuncu:
Quote from: RonR on March 25, 2012, 06:02:43 am
To use a Voice Gateway with a SIP provider, either SP1 or SP2 will have to be configured as SIP. Google Voice is not a SIP provider.
In an earlier post, you said you had Callcentric on SP2. If that's the case, the VG3 AccessNumber should be : SP2(sip.poivy.com)
What does the OBi Call History show for the failed call?
Yes I have set up another obi for my sister. She did not have a land line so for her I had to get callcentric as SP2.
Now I have configured one for myself but I do have a basic landline so I did not bother to configure callcentric.
After your suggestion I have setup a callcentric account and everything worked like a charm. Do you know if callcentric will cancel my account if I don't make any calls from it. I saw this was the case with callwithus. Or do you have any other suggestions for sip providers.
Thanks for all your help
T
Navigation
[0] Message Index
[#] Next page