Need help to setup PSTN for OBI110
Qnewbie:
As attracted by many introductions that OBI110 is a better replacement of Linksys' SPA products, I bought one OBI110. I resides in Sweden and cannot set up properly for passing the incoming PSTN call to the phone with OBI110! ???
Following the guideline by Leftright(http://www.obitalk.com/forum/index.php?action=printpage;topic=679.0)
Tone setting changed to:
Dial tone: 425-18;20
Ringback tone: 425-18;-1;(1+5)
Busy tone: 425-18;20;(.25+.25)
Reorder tone: 425-18;20;(.25+.75)
LINE port setting changed to:
DetectPolarityReversal: Check
DetectFarEndLongSilence: Check
SilenceDetectSensitivity: medium
SilenceTimeThreshold: 60
ACImpedance: 270+(755||150 nF) and ...
CallerIDDetectMethod: DTMF(Finland,Sweden)
PHONE port setting changed to:
Impedance: 270+(755||150 nF)
CallerIDMethod: DTMF(Finland,Sweden)
The phone rings when there is incoming call. I pick up the phone, there is only dial tone. OBI110 does not even connect the incoming call to the phone. Any hints are welcome! TIA!
/Qnewbie
PS.:
Both the LINE & PHONE led light up.
1. Disconnect the power adaptor from OBi110
2. Lift up your analog phone, do you hear dial tone ?
Yes
3. hang up your phone, wait ~3 second, and off hook again.
do you hear dial tone ?
Yes again.
Stewart:
From the phone connected to the OBi, can you:
Run the echo test (dial **9 222 222 222)?
Make VoIP calls?
Receive VoIP calls?
Make PSTN calls? (If Primary Line is not PSTN, try dialing **8 + PSTN number.)
Dial # and hear PSTN dial tone? If so, can you then successfully call a PSTN number?
On a failing incoming PSTN call, what does caller hear when you answer phone connected to the OBi? If you log into the OBi directly, what does Call History show for the failed call?
Qnewbie:
Quote from: Stewart on May 25, 2012, 02:28:31 pm
From the phone connected to the OBi, can you:
Run the echo test (dial **9 222 222 222)?
Make VoIP calls?
Receive VoIP calls?
Make PSTN calls? (If Primary Line is not PSTN, try dialing **8 + PSTN number.)
Dial # and hear PSTN dial tone? If so, can you then successfully call a PSTN number?
On a failing incoming PSTN call, what does caller hear when you answer phone connected to the OBi? If you log into the OBi directly, what does Call History show for the failed call?
Echo test works.
Making VOIP calls are OK.
Receiving VOIP calls are OK.
Making PSTN calls are OK.
The only problem is incoming PSTN call. I just hears ringback tone(on my mobile) when I pick up the phone(only dial tone). Here is call history(failed call):
Call 1 05/26/2012 10:20:26
Terminal ID LINE1 PHONE1
Peer Name
Peer Number
Direction Inbound Inbound
10:20:26 Ringing
10:20:28 End Call
Call 2 05/26/2012 10:20:08
Terminal ID LINE1 PHONE1
Peer Name
Peer Number
Direction Inbound Inbound
10:20:08 Ringing
10:20:10 End Call
I think this is setting's problem but don't have any clue.
In Sweden, there is not disconnection tone. The start and end of call are signalled by polarity switch.
Stewart:
Interesting. How does the log relate to your actions? (Did you post two separate attempts, or is one actual call logged as two or more calls in the OBi? Did you answer within two seconds, or did the OBi generate the End Call event on its own?)
If you attempt to answer a PSTN call, hear dialtone and then press #, does that pick up the landline? If not, try setting EnableLINEPortBargeIn for the Phone port and test again.
When a phone is connected directly to the PSTN line (OBi not in system), what is the approximate ring cadence (e.g. two seconds on, four seconds off)? Does your PSTN line have caller ID?
Qnewbie:
Quote from: Stewart on May 26, 2012, 03:37:54 am
Interesting. How does the log relate to your actions? (Did you post two separate attempts, or is one actual call logged as two or more calls in the OBi? Did you answer within two seconds, or did the OBi generate the End Call event on its own?)
It is log for one call.
Quote
If you attempt to answer a PSTN call, hear dialtone and then press #, does that pick up the landline? If not, try setting EnableLINEPortBargeIn for the Phone port and test again.
It picks up the landline but drops after a few seconds(or less). EnableLINEPortBargeIn is checked, the same result holds. Strange that there is not log in the call history.
Quote
When a phone is connected directly to the PSTN line (OBi not in system), what is the approximate ring cadence (e.g. two seconds on, four seconds off)? Does your PSTN line have caller ID?
Ring cadence is one second on, four seconds off. My PSTN line does not have CID for incoming calls.
Navigation
[0] Message Index
[#] Next page