Dial plan explanation
Gennady:
Thanks Ron, I reset OBI to factory default and manually type everything back, and now flash working. I suspect that during my “experiments” I setup a wrong value somewhere. Now my settings for Physical Interfaces -> LINE Port -> DigitMap: ([2-9]11S0|[2-9]xxxxxxxxx|3xxxxxx|<8044:**2>xxxxxxx).
Could you please tell me of how I should direct all international calls started with 011 to SP1?
RonR:
Quote from: Gennady on February 24, 2012, 01:59:51 pm
Now my settings for
Physical Interfaces -> LINE Port -> DigitMap: ([2-9]11S0|[2-9]xxxxxxxxx|3xxxxxx|<8044:**2>xxxxxxx).
Could you please tell me of how I should direct all international calls started with 011 to SP1?
Physical Interfaces -> LINE Port -> DigitMap:
([2-9]11S0|[2-9]xxxxxxxxx|3xxxxxx|<8044:**2>xxxxxxx|<**1>011xx.)
brav:
what does this part of the dialplan do? is it for speedials?
{([1-9]x?*(Mpli)):pp}
like it takes 1 or 2 digits with a star after and sends it to primary line..but for what?
thanks!
RonR:
Quote from: brav on February 27, 2012, 01:22:38 am
{([1-9]x?*(Mpli)):pp}
One or two digits followed by an asterisk followed by a number that matches the PrimaryLine DigitMap rules is sent to the OBiTALK Service trunk. This is for single-stage dialing from OBi's and OBiON Apps (limited to using the PrimaryLine).
jimates:
RonR,
I am doing some clean up and simplification in one of my Obi's.
What can I do to clean these up some, and what is Msp1. It is present in some default settings but removed in some custom settings.
ITSP Profile
Digit Map - (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<1814>[2-9]xxxxxx|011xx.)
SP1 - X_InboundCallRoute - {ph,pp(290xxxxxx|290xxxxxx|290xxxxxx)}
Obitalk Service
Digit Map
(<ob>xxxxxxxxx|obxxxxxxxxx)
InboundCallRoute – (3 Obion softphone numbers with this Obi set as the default gateway and direct dialing, same as from the phone port)
{(290xxxxxx|290xxxxxx|290xxxxxx)>(xx.):SP1},{(290xxxxxx|290xxxxxx|290xxxxxx)>(<**2:>xx.):SP2},{(290xxxxxx|290xxxxxx|290xxxxxx)>(<**8:>xx.):LI},{(290xxxxxx|290xxxxxx|290xxxxxx):aa},{ph}
Phone Port - (I know I should move the 411 to the digit map and out of the call route. This was done long long ago when we first got Obi’s, and since it worked I didn’t worry about it.)
Digit Map
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|411|**0|***|#|**1{t=di2}(Msp1)|**2{t=di2}(Msp2)|**8{t=od}(Mli)|**9{t=di2}(Mpp)|(Mpli))
OutboundCallRoute –
{(<411:18002464411>):sp1}, {([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Navigation
[0] Message Index
[#] Next page
[*] Previous page