Dial plan explanation
RonR:
yiucsw,
You want to leave the OutboundCallRoute configured normally and set:
Physical Interfaces -> PHONE Port -> DigitMap : (<S0:12341234567>)
where 12341234567 is your mobile number.
RossL:
Hi guys,
I’ve recently purchased a couple of Obi110’s which I am setting up for use within Australia (replacing SPA3000's) but I’m having problems getting my head around the DigitMaps etc. At present, the Phone Port DigitMap and Phone Port OutboundCallRoute are still set to their default values.
As the bulk of all my calls are made via my VoIP provider (I only use one), I have their details set under ITSP Profile A and also have set:
Physical Interfaces -> PHONE Port -> PrimaryLine : SP1 Service
My current SPA3000 dial plan (which I would like to replicate) is as follows:
(000S0<:@gw0>|1100S0<:@gw0>|1800xxxxxxS0<:@gw0>|13[19]xxxS0|1300xxxxxxS0|1900xxxxxx!
|77[1578]S0|0011xx.|[45689]xxxxxxxS0|0[23478]xxxxxxxxS0|xx.)
This translates to:
000 (the Australian equivalent of 911), 1100 and 1800xxxxxx via PSTN
13[1-9]xxx, 1300xxxxxx, 77[1578], 0011xx. , [45689]xxxxxxx and 0[23478]xxxxxx via SP1
1900xxxxxx barred
xx. (anything else via SP1)
Can you advise what I need to achieve this. Thanks.
RonR:
Physical Interfaces -> PHONE Port -> DigitMap:
([1-9]x?*(Mpli)|[1-9]|[1-9][0-9]|000|**0|***|#|**1(Msp1)|**2(Msp2)|**8(Mli)|**9(Mpp)|(Mpli))
Physical Interfaces -> PHONE Port -> OutboundCallRoute:
{([1-9]x?*(Mpli)):pp},{(<#:>|000):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},
{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Service Providers -> ITSP Provider A -> General -> DigitMap:
(<**8>1100|<**8>1800xxxxxx|!1900xxxxxx|13[1-9]xxx|1300xxxxxx|77[1578]|
0011xx.|[45689]xxxxxxx|0[23478]xxxxxx|xx.|(Mipd)|[^*]@@.)
Physical Interfaces -> LINE Port -> DigitMap:
(xxxxxxS4|1xxxxxxxxx|xx.)
Note: The rules in boldface can be omitted as they'll be caught by the xx. rules.
000 -> PSTN
1100 -> PSTN
1800 + 6 digits -> PSTN
1900 + 6 digits -> Barred
Everything else -> SP1
RossL:
Hi RonR,
Thanks for the response. All seems to be working OK, but obviously I can't test 000.
Prior to making these changes, I could press # on the phone and it would immediately swap to the PSTN line with the PSTN line dial tone so I could make calls manually. Now when I press #, there is a pause of about 10 secs, then the OBi110 seems to reset; the OBi phone and line lights start blinking, they go off and the power light turns red; then all the lights come back green. At the point the power light goes red, the PSTN dial tone is heard but when the lights come back green then the OBi generated dial tone returns.
Is another entry required to re-enable the # connecting immediately to the PSTN line?
RonR:
Pressing only a # should not have changed. It still should bridge you immediately to the LINE Port.
The OBi should not be rebooting. Recheck your DigitMaps and OutboundCallRoute for a typo.
There is no error checking in the OBi, so incorrect entries can cause the OBi to simply reboot.
Navigation
[0] Message Index
[#] Next page
[*] Previous page