Nymgo on OBi100
cyclops:
Hello, my first post here. So far my experience with OBi has been really well and the setup process for Google Voice was a breeze.
But now I want to get a second provider (SP2) setup done my device. I am a noobie when it comes to VOiP.
I have an account with Nymgo and want to set it up in my OBi100 as a SP2 which would trigger only when I dial 011 (for international calls), all my other calls should be routed to SP1 (google voice). Is this kind of setup possible at all? I have got the following details from nymgo website, but I am still not able to set the account on my OBi.
Connect your SIP device
To connect your SIP device to Nymgo, please use the below configuration:
SIP Server Or SIP Proxy Server: ata.nymgo.com
SIP User ID: nymgo username
Authenticate ID: nymgo username
SIP password: nymgo password
SIP Port: 5060
Codec Used: g729, g711
STUN Server: stun.nymgo.com
STUN port: 80
Nymgo supports Codecs G729 and G711
You may test whether your SIP device is configured correctly, by dialing 111 (free testing number).
You may also check your balance by dialing 999 (free number), the balance will be given in US Dollars
I have entered the details in the SP2 section, but now what? How do I test if I can make calls from SP2? And once I am able to set it up successfully as SP2 and able to make calls, how do I configure so that the SP2 is used only when I dial 011?
QBZappy:
Quote from: cyclops on June 29, 2012, 12:55:31 pm
I have an account with Nymgo and want to set it up in my OBi100 as a SP2 which would trigger only when I dial 011 (for international calls), all my other calls should be routed to SP1 (google voice). Is this kind of setup possible at all? I have got the following details from nymgo website, but I am still not able to set the account on my OBi.
cyclops,
Welcome.
Connect your SIP device
You may test whether your SIP device is configured correctly, by dialing 111 (free testing number).
You may also check your balance by dialing 999 (free number), the balance will be given in US Dollars
I have entered the details in the SP2 section, but now what? How do I test if I can make calls from SP2? And once I am able to set it up successfully as SP2 and able to make calls, how do I configure so that the SP2 is used only when I dial 011?
If you have entered the registration settings correctly you will see something like this by looking at the the OBi web page. (Dial ***1 to obtain ip address of your unit):
Status->System Status->SP2 Service Status->Status = Registered (server=111.222.333.444:5060; expire in 53s)
If it does show as "Registered" then you have succeed. What's left is to test it by dialing **2111 (echo test number) or **2999 (for balance amt)
If you want 011 to go automatically over SP2: eg <**2>[011]x.
(to be more efficient if you know the number of digits to dial in advance is always the same replace x. with xxxxxxxxx or whatever)
Without making any changes to the PHONE Port DigitMap or OutboundCallRoute the above mentioned setting
added to your PrimaryLine (SP2 / ITSP Profile B) DigitMap, will enable dialing 011 (without dialing **2) will be automatically redirected over the SP2 provider.
cyclops:
Quote from: QBZappy on June 29, 2012, 02:06:51 pm
Quote from: cyclops on June 29, 2012, 12:55:31 pm
I have an account with Nymgo and want to set it up in my OBi100 as a SP2 which would trigger only when I dial 011 (for international calls), all my other calls should be routed to SP1 (google voice). Is this kind of setup possible at all? I have got the following details from nymgo website, but I am still not able to set the account on my OBi.
cyclops,
Welcome.
Connect your SIP device
You may test whether your SIP device is configured correctly, by dialing 111 (free testing number).
You may also check your balance by dialing 999 (free number), the balance will be given in US Dollars
I have entered the details in the SP2 section, but now what? How do I test if I can make calls from SP2? And once I am able to set it up successfully as SP2 and able to make calls, how do I configure so that the SP2 is used only when I dial 011?
If you have entered the registration settings correctly you will see something like this by looking at the the OBi web page. (Dial ***1 to obtain ip address of your unit):
Status->System Status->SP2 Service Status->Status = Registered (server=111.222.333.444:5060; expire in 53s)
If it does show as "Registered" then you have succeed. What's left is to test it by dialing **2111 (echo test number) or **2999 (for balance amt)
If you want 011 to go automatically over SP2: eg <**2>[011]x.
(to be more efficient if you know the number of digits to dial in advance is always the same replace x. with xxxxxxxxx or whatever)
Without making any changes to the PHONE Port DigitMap or OutboundCallRoute the above mentioned setting
added to your PrimaryLine (SP2 / ITSP Profile B) DigitMap, will enable dialing 011 (without dialing **2) will be automatically redirected over the SP2 provider.
You are awesome! Thanks, the setup is successful.
BUT, I still did not get where exactly do I need to change the settings to enable using SP2 as default when I start dialing 011.
QBZappy:
cyclops,
Service Providers->ITSP Profile B->General->DigitMap =
Default:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)
Change to:
(<**2>[011]x.|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)
cyclops:
Many thanks for a quick revert..
But somehow I am not able to edit any of the values there. No matter what I type it does not gets printed there, even the copy paste is not working.
P.S. Is there a rep system on this board?
EDIT: Got it, we need to uncheck the 2 checkboxes to enable editing. What a weird step.
Navigation
[0] Message Index
[#] Next page