Calling from Google Voice using OBi (solved)
GregoryZ:
Jeff,
I've been reading this post some over the past couple of days. I guess I wasn't paying too much attention. It didn't sink in when I read you had just done a reset. :)
Blew my thoughts out of the water. :-\
I just tested my click to call. It works fine. I don't get the call screening option (Jimates question earlier) either.
Quote from: jimates on August 20, 2012, 09:40:48 pm
If I try and have it ring my OBi phone it does not ring but the call still goes through but I am not connected to it, the people at the number I am calling hear nothing.
The call you place using "click to call" should not even ring the other person's phone until you have answered your forwarding phone. You say your Obi doesn't ring, but somehow the call is being answered or the call would not be delivered to the other party.
I agree with Jimates here too. The call should not be made to the other party until you have first picked up your phone connected to the OBi.
I'm stumpped too. If it wasn't for the fact that you have just reset your OBi, I'd have you look up that information. ( I see QBZappy jumped in before I finished typing this. His link will get you the info I was asking for)
I've seen several posts where GV has been giving folks Busy Signals when the numbers they were calling are not busy, and misc. other issues that seem isolated and random. Maybe this is just the case for your situation.
If you had another OBi to setup with the same GV account, and test it there that would give us a better idea if it was in fact the OBi or not.
-G
jeff@jeffmusto.com:
<<Both settings can be found by clicking on this link: (Insert your OBi ip)
http://YOUR_OBI_IP/VS_1_VP_1_L_1_.xml>>
And how would I find my OBi IP address?
jeff@jeffmusto.com:
<<I've seen several posts where GV has been giving folks Busy Signals when the numbers they were calling are not busy, and misc. other issues that seem isolated and random. Maybe this is just the case for your situation.>>
The call is going through. I can call my home (and other numbers) and the number I dial picks up the phone but of course I am not there.
I can also see the network light blink with activity when I do a click to call. I thought maybe my phone was not ringing but when I answer my phone (when it has not rang but I see the network light blinking) I just have a dial tone.
I have a new OBi coming by next Monday so I can try the new one then.
jeff@jeffmusto.com:
I figured out my IP address
Post your SP1 > X_InboundCallRoute
{(x.6124245445|x.xxxxxxxxxx):aa},{ph}
Also make sure that > X_SkipCallScreening is checked.
This is checked
GregoryZ:
Good Morning Jeff,
1st, you may want to edit your last post. put "XXXX or ###" or so, in the post to hide a few digits of your phone number. It's just a suggestion for YOUR security. :)
2nd, OK. So you've just done a reset of your device, yet you have a digit map in your call route already. I'm no "Digit Map/Dial Plan" expert at all. In fact, I rely on the others here for that.
But, what comes to my mind is; if you have done a Hard Re-set, and have a non Defult setting here... where else may there be a non-default setting.
EDIT: I just got back from walking the dog, but I was thinking.... The inbound call route might be your numbers that you put in as "Circle of Trust" numbers on OBiTalk. I don't know. But, are either of those numbers your GV number? Maybe that is throwing things off.
Does anyone else agree? Should we not be looking closer at what Jeff's OBi Settings are at this point?
-G
Navigation
[0] Message Index
[#] Next page
[*] Previous page