OBiAPP & X Lite Setup Configurations?
GregoryZ:
Close the X-Lite.
Make sure that OBiAPP is running, and you are Logged In.
Then start X-Lite.
Some folks say that have better luck entering the address(s) like this: 127.0.0.1:5060
All this does is specify to use port 5060
I've beat myself up trying to get the OBiAPP and a Softphone to work, but I gave up. I'm really not going to be much help, I'm afraid. :-\
-G
tavie888:
Hello GregoryZ,
I managed to get X-Lite v 5 working with OBiAPP!
1. In OBiTALK Portal >OBi ExpertConfig > System Management >NetworkSetting, I found that my Internet Settings section was somehow completely devoid of settings. No wonder why X-Lite had a hard time getting enabled. So, I had to manually enter IP address of the OBi110 unit, subnet, default gateway and DNS server.
2. Un-install X-Lite then reboot.
3. Re-install OBiAPP. After logging in, all previous correct settings show up:
OBiTALK Number: 290 xxx xxx
Voice Gateway: 200 xxx xxx
Advanced Tab:
SIP domain or proxy local address:
IP address: (select) "default"
SIP Port:5060
RTP Port:36000
OBiTALK address:
IP address: (select) "default"
Signalling port: 10000
RTP Port: 36100
4. Re-install X-Lite and make sure to uncheck "Start X-Lite when Windows starts". This ensures that X-Lite does not start running before OBiAPP does.
By the way, how do I get OBiAPP to start when Windows start? Or is this really necessary, because I don't always use softphone. I think I may need to remind myself whenever I want to make calls using X-Lite I have to open OBiAPP first.
Important settings in X-Lite:
Account name: OBiAPP
Protocol: SIP
UserID: 290xxxxxx (OBi number of softphone device)
Domain: 127.0.0.1
Domain proxy: check box "Register with domain and receive calls"
Send outbound calls via proxy address: 1270.0.1:5060
Topology Tab:
Firewall traversal: (select) None
Check radio box: Range of ports used on local PC: 5060-5080
The rest of the settings in X-Lite are default values.
5. X-Lite now appears normal, i.e. without error messages.
6. The Status Tab in OBiAPP now shows:
Softphone client state: registered
Contact:<sip:290xxxxxx:5062>
Note: Ports 5060, 5061 and 5062 are for OBi110 unit, SP1 and SP2, respectively.
I hope the info in this post is useful for some members, especially new users.
:)
jimates:
move, or copy, the Obiapp application to the startup folder in your all programs. Obiapp will then start when windows starts.
GregoryZ:
Quote from: tavie888 on August 24, 2012, 08:00:18 pm
Hello GregoryZ,
I managed to get X-Lite v 5 working with OBiAPP!
Great!!
Quote
1. In OBiTALK Portal >OBi ExpertConfig > System Management >NetworkSetting, I found that my Internet Settings section was somehow completely devoid of settings. No wonder why X-Lite had a hard time getting enabled. So, I had to manually enter IP address of the OBi110 unit, subnet, default gateway and DNS server.
If your OBi's AddressingType was set at it's defult of DHCP, then those settings should have been set by your router's DHCP server. But, entering them as Static doesn't hurt. I'm not sure how much of that makes a difference.
Quote
By the way, how do I get OBiAPP to start when Windows start?
Put a shortcut in your statup folder. See this link for tips:
http://www.obitalk.com/forum/index.php?topic=2038.msg12938#msg12938
Also, if you right click the OBiAPP while it is in your system tray, Logoff and then Login again, it will start the next time, already minimized to the system tray.
Now you can have X-Lite auto start. (It always takes a min. for it to start, so by then the OBiAPP wil be running.)
There are a couple of things you have done different then what I've tried in the past.
1) You only put the :5060 after the Proxy Address. If I remember, I had always put it in both places.
2) Putting a Check for the Range of Ports. This never worked for me. A few others have also said it wouldn't allow them to connect when they had it selected.
Quote
I hope the info in this post is useful for some members, especially new users. :)
Now that you have this up and running..... Here is where I gave up.....
After a while, sometimes minutes, sometimes hours..... of idle time, it all quits working. Even when the X-Lite shows it's registered, it won't ring. Even making calls sometimes fails. This is why I have been saying I can't get it to work.
So, if you find that you're able to consistantly Recieve and Make calls, even after periods of idle time, let me know.
Most users who have set this all up have been able to get X-Lite registered and working, but it all just stops working correctly after a while, and requires a restart of the whole setup.
PLEASE, if you can, keep the X-Lite running as long as you can, and test it every so often. I've had it all working for as long as overnight. But came back from work, and it was down. :(
I look forward to your Progress Report.
-G
GregoryZ:
tavie888,
You may also be interested in this post: http://www.obitalk.com/forum/index.php?topic=392.msg3328#msg3328
-G
Navigation
[0] Message Index
[#] Next page
[*] Previous page