I'd like to be able to use lines on my Obi110 when the Phone port is being used.
I'd like the Phone port of the PAP2 to accomplish exactly the same as the Obi110
I'm using the following instructions:
Quote from: RonR on August 22, 2011, 07:23:45 PM
QuoteAt least one Voice Service (SP1/SP2) must be configured for SIP. It need not be registered with a SIP provider. If you're not using a SIP provider, you must still set ProxyServer (127.0.0.1 is fine) and you should disable X_RegisterEnable.
For PAP2 -> OBi, the PAP2 is set to not register and to make and receive calls without registration. The UserID is unimportant (I used pap2) and the Password is not used. The proxy server must be set to the OBi's IP address and port. The port number must be set to 5060 for SP1 or 5061 for SP2.
For OBi -> PAP2, I use Voice Gateway5:
Name: PAP2
AccessNumber : SP2(192.168.1.145:5062)
SP2 is the Voice Service I have configured for SIP. The PAP2 is at 192.168.1.145 on port 5062.
Voice Services -> SP2 Service -> InboundCallRoute is set to:
{pap2>([1-9]x?*@@.):pp},{pap2>911:li},{pap2>**0:aa},{pap2>***:aa2},{pap2>(<**1:>(Msp1)):sp1},
{pap2>(<**2:>(Msp2)):sp2},{pap2>(<**8:>(Mli)):li},{pap2>(<**9:>(Mpp)):pp},{pap2>(Msp1):sp1},
{pap2>0:ph},{pap2:},{ph,vg5(pap2)}
This allows most of the PHONE Port dialing features to be mimicked from the PAP2.
All other InboundCallRoutes are set to: {ph,vg5(pap2)}
This causes both the PHONE Port and the PAP2 to ring on incoming calls.
As I have an Xlink plugged in to the Line I'm using the following setup:
I am using tg1
TrunkList: li1,vg3
Digitmap: (Mli)
When the Cellphone is not connected to the Xlink there is no Voltage and default calls (in other words numbers without any **x preceding them in the li Digitmap) are sent to vg3. Once there they are adjusted by vg3s Digitmap to change them to international format for the VoIP provider.
What could I do to get the PAP2 to work exactly as the Phone port of the Obi110 works?
I adjusted the following:
Voice Services -> SP2 Service -> InboundCallRoute is set to:
{pap2>(Mli):tg1},{pap2>([1-9]x?*@@.):pp},{pap2>(<#:>|1xx):li},{pap2>**0:aa},{pap2>***:aa2},{pap2>(<**1:>(Msp1)):sp1},{pap2>(<**2:>(Msp2)):sp2},{pap2>(<**3:>(Mvg3)):vg3},{pap2>(<**4:>(Mvg4)):vg4},{pap2>(<**6:>(Mvg6)):vg6},{pap2>(<**7:>(Mvg7)):vg7},{pap2>(<**8:>(Mli)):li},{pap2>(<**9:>(Mpp)):pp},{pap2>0:ph},{pap2:},{ph,vg5(pap2)}
I've just got a basic (xx.|**x.) dial plan on my PAP2 but I'll have to change that.
Everything seems to be working great... Except:
On incoming calls I can hear but not be heard.
On Outgoing calls no audio at all.
