Voice Gateway Setup
ArbitaryTwist:
I was trying to follow this post to setup the Voice Gateway 3, but i can't figure out the ITSP parts.
http://www.obitalk.com/forum/index.php?topic=1063.0
I have Freephoneline.ca setup on SIP1, Google Voice on SIP2, and i would like to add VOIPJumper on Gateway 3, such that if someone dials 01191xxxxxxxxxx, the call is routed through VOIPJumper. Would appreciate the help. Just got my device yesterday so learning a few tricks i guess.
I should say that i am using an OBI110, but no physical line present.
RFord:
Do you know if VOIPJumper allows calls WITHOUT registration? In order for you to use a VOIP provider on one of the OBi's Gateways, that provider must allow calls without the ATA being registered to their Server. Also, since your SIP provider is set up on SP1, then:
Access Number : SP1(sip.voipjumper.com)
ianobi:
ArbitaryTwist,
RonR's post explains changes needed to add VG3 to Phone Port DigitMap and OutboundCall Route. RFord has explained regarding AccessNumber. All that remains is for you to add this rule at the front of the DigitMap of which service is your PrimaryLine:
(<**3>01191xxxxxxxxxx|...
By default in the OBi110 the following is true:
Msp1 = Service Providers -> ITSP Profile A -> General -> DigitMap
Msp2 = Service Providers -> ITSP Profile B -> General -> DigitMap
Felix:
Quote from: RFord on February 15, 2013, 04:06:50 am
Do you know if VOIPJumper allows calls WITHOUT registration?
Looks like one of Betamax companies, so the answer is likely to be yes. Note that to call abroad you dial 00xxx, not 011xxx! So, rather than using **3 prefix, you can route numbers that start with 00 to the gateway.
And if you dial both FreePhoneLine and GV with all 11 digits (12125551212), then you can channel all non-1 numbers to the gateway using something like <:00>[2-9]xxx.
ArbitaryTwist:
Thanks for the reply guys. Sorry took me a bit to get back.
Well i am not sure if VOIPJumper supports calling without registration, but i need to find out.
So far i have made the following changes.
Physical Iterfaces -> PHONE Port -> DigitMap:
([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**8(Mli)|**9(Mpp)|(Mpli))
Physical Iterfaces -> PHONE Port -> OutboundCallRoute:
{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Service Providers -> ITSP Profile A -> General -> DigitMap:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|<**3>011xx.|xx.|(Mipd)|[^*#]@@.)
Gateways and Trunk Groups -> Voice Gateway3
Enable - Yes
Name - VOIPJumper
AccessNumber - SP1(sip.voipjumper.com)
DigitMap : (<011:00>xx.|00xx.)
AuthUserID : username
AuthPassword : password
When i dial using 011, it says service not available. Maybe its a problem with VOIPJumper registration.
@Felix -> To call out of North America, you need to use 01191xxxxxxxxxx.
When i dial out it says "No Service Configured Error. Please logon to Obitalk.com........."
Anything i am doing wrong? Is there a test SIP client i can use to see if my settings are correct?
Navigation
[0] Message Index
[#] Next page