Voice Gateway Setup
ArbitaryTwist:
Quote from: azrobert on February 21, 2013, 09:12:27 am
Un-register VOIP Jumper using your working setup on SP2.
Voice Services => SP2 service: X_RegisterEnable = unchecked
This will tell you if they accept un-registered outbound calls.
Works fine with Register Unchecked. So definately registration is not required.
azrobert:
I don't see the problem, but try the below configuration. Why dial **3011xx or 011xx and have it converted to 00xx? Just dial 0091xxxxxxxxxx
Physical Interfaces -> PHONE Port -> DigitMap:
((Mvg3)|[1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**8(Mli)|**9(Mpp)|(Mpli))
Physical Interfaces -> PHONE Port -> OutboundCallRoute:
{(Mvg3):vg3},{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Service Providers -> ITSP Profile A -> General -> DigitMap:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|xx.|(Mipd)|[^*#]@@.)
Gateways and Trunk Groups -> Voice Gateway3
Enable - Yes
Name - VOIPJumper
AccessNumber - SP1(sip.voipjumper.com)
DigitMap : (00xx.)
AuthUserID : username
AuthPassword : password
zapattack:
Question for anyone using Voice Gateways.
How long does it take for a VG call to complete? My Obi 110 takes a minimum of 10 seconds, but SP calls only take 2 seconds.
Testing with a LinkSys unit to unregistered provider shows completion in about 2 seconds also.
Tried using all the recommended configurations in the Forum.
ArbitaryTwist:
Quote from: azrobert on February 21, 2013, 08:38:23 pm
I don't see the problem, but try the below configuration. Why dial **3011xx or 011xx and have it converted to 00xx? Just dial 0091xxxxxxxxxx
Physical Interfaces -> PHONE Port -> DigitMap:
((Mvg3)|[1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**8(Mli)|**9(Mpp)|(Mpli))
Physical Interfaces -> PHONE Port -> OutboundCallRoute:
{(Mvg3):vg3},{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Service Providers -> ITSP Profile A -> General -> DigitMap:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|xx.|(Mipd)|[^*#]@@.)
Gateways and Trunk Groups -> Voice Gateway3
Enable - Yes
Name - VOIPJumper
AccessNumber - SP1(sip.voipjumper.com)
DigitMap : (00xx.)
AuthUserID : username
AuthPassword : password
As far as i understand, you have to dial 011 to dial out of USA/Canada. So don't think the 0091xxxxx will work.
azrobert:
<011:00>xx. in your digit map changes 011xx. to 00xx., so when you dial 01191xxxxx, 0091xxxxx is sent to VOIP Jumper.
If you need 01191xxxxxx sent to VOIP Jumper change the DigitMap in the Voice Gateway 3 in my config example to (011xx.), then dial 01191xxxxxx
Navigation
[0] Message Index
[#] Next page
[*] Previous page