How to configure dial plan for SIP URI dialing with callcentric?

(1/2) > >>

kindnation:
I have Google Voice on SP1, and use Callcentric on SP2 just for the SIP URI dialing.

To do SIP URI dialing, you would normally dial **275* + the SIP number to dial out through SIP Broker.

I would like to be able to just dial ** + SIP number, and be able to automatically send the **275* + SIP number through SP2 (Callcentric).


Can you advise where I would configure this dial plan and the necessary format to get it to just use ** instead of the full **275* ?  Any help would greatly be appreciated.

ianobi:
kindnation – welcome to the forum.

More info needed! Do you have an OBi100, OBi110 or OBi202?

Can we assume that GV on sp1 is your Primary Line (no ** codes needed)? So you dial **2 to access Callcentric on sp2? This means that to dial a sipbroker number on Callcentric you presently have to dial **2**275* + SIP number?

Does the following DigitMap look like this?
Service Providers > ITSP Profile B > General > DigitMap:
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)

ianobi:
The easiest solution is to set up a voice gateway and call sipbroker direct. I’ll use voice gateway 3 in this example. I’ll assume you have an OBi100 as it is the most simple:

Additions are needed – shown in bold:

Physical Interfaces > PHONE Port > DigitMap:
 ([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|**1(Msp1)|**2(Msp2)|**3(Mvg3)|**9(Mpp)|(Mpli))

Physical Interfaces > PHONE Port > OutboundCallRoute:
{([1-9]x?*(Mpli)):pp},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Mvg3)):vg3},{(<**9:>(Mpp)):pp},{(Mpli):pli}


Next set up the voice gateway:

Voice Services > Gateways and Trunk Groups > Voice Gateway3  >

Access Number: sp2(sipbroker.com)
DigitMap: (<*>xx.|*xx.)

Now simply dial **3 + sip number.

Edit: corrected a "cut and paste" error - must stop copying from my other posts  :)

azrobert:
Depending on your requirements you might be able to also eliminate SipBroker.

Just define a Voice Gateway for each URI you want to call.
Then setup a calling scheme like ianobi suggested to call each Voice Gateway.

kindnation:
Quote from: ianobi on March 07, 2013, 05:15:56 am

kindnation – welcome to the forum.

More info needed! Do you have an OBi100, OBi110 or OBi202?

Can we assume that GV on sp1 is your Primary Line (no ** codes needed)? So you dial **2 to access Callcentric on sp2? This means that to dial a sipbroker number on Callcentric you presently have to dial **2**275* + SIP number?

Does the following DigitMap look like this?
Service Providers > ITSP Profile B > General > DigitMap:
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)




Thank you so much for the warm welcome and trying to help me get this working.  To answer your question, I have an OBI-100 and yes to all of them.

I also added to > ITSP Profile A General > (<**2>1777xxxxxxx|<**2>**275*x.|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*]@@.)

So I am now able to dial **275*(SIP URI) and it will go through to my Callcentric on SP2 automatically.  I would like to be able to just dial **(SIP URI) and have it work.  I know it's only saving me pressing 4 extra buttons, but is there a way to do it?

thanks for your help!

Navigation

[0] Message Index

[#] Next page