Can't connect my IP Phone to my OBi202
N7AS:
I have been trying to connect my Yealink SIP-T28P IP phone to my OBi202 so I can make and answer calls on this phone. I tried all the options here with no luck. There is no way on the Yealink phone to set "make calls without reg" and "answer calls without reg" as this is what is required. Cisco phones have this feature.
I do have an unfunded account with voip.ms and usere can call other users free. I wonder if this could be done using voip.ms sub accounts that will register on the OBi202 and the Yealink phone and bridge calls through the OBi202.
On my OBi202
SP1 - Google Voice
SP2 - Anveo free account - Used to receive various DID calls via SIP URI.
SP2 - Localphone - For international calls
SP4 - open
I was also thinking that maybee I could rout calls through my OBi110 which is online but both SP1 and SP2 are disabled.
Any ideas?
hwittenb:
N7AS
I believe you could do it thru PBXes.com which offers free accounts when you use less than 2000 minutes a month and have a limited number of extensions and simultaneous calls. They have a feature called Sub PBXes which makes it fairly easy. You could also do something similiar with your own Asterisk system.
Setup and register your ip phone as the "Main" extension. For example extension 200 you would register to userid-200@pbxes.org
Setup a Sub PBXes SubPBX. For example userid-400. On the OBi use a spare SPx to register to this SubPBX ... userid-400@pbxes.org
Setup a PBXes Outbound Routing Valid for all (dialed) numbers to the SubPBX that you just setup.
The default / Incoming Route should send an incoming call (from the OBi) to Extension 200.
Dialed calls from your ip phone should now go to the OBi SPx you registered to the SubPBX.
Edit: So on your PBXes account you have 1 extension, 1 SubPBX, 1 Outgoing Route, 1 Incoming Route.
On the OBi SPx setup X_InboundCallRoute to dial the number that comes in with the call on the outgoing facility you wish. For example {(200)>xx.:SP2} which will dial incoming dial calls from extension 200 out on SP2.
On the OBi setup your potential incoming calls to the OBi to ring the ip phone in addition to the phone(s) on the OBi. To do this you would fork the incoming calls to SPx(200) in addition to the phone(s). For example {SP4(200),ph,ph2} if you had SP4 registered to PBXes.
Edit: As an aside, during testing I discovered you do not want to have your OBi Sip account setup to use TCP. It needs to be setup to use the default UDP. PBXes would not send the call on the outgoing trunk (subpbx) about half the time when the sip communication was by TCP. I had set it up for TCP some time previously to talk to my android phone.
N7AS:
hwittenb,
I think this may work better. I will see if I can try it later. I do have a free pbxes account. I wish someone would write a tutorial for pbxes. Maybee Stewart is still reading this forum.
I did try the following today...
I registered 3 voip.ms sub accounts on 3 of my devices.
Ext 101 - OBi202 SP$
Ext 102 - Yealink SIP-T28P
Ext 102 - Linksys SPA941 Line 3
---------
I tried to call between extensions. Just got a busy line. The other extension did not ring. So, I may be wrong, but I think calls between extensions need a funded account.
So, your method would be a little easier as long as I can figure out pbxes once again. I haven't used it for quite awhile.
zapattack:
Not sure if you can dial between sub-accounts, as each is by definition stand-alone(?)
I think extension dialing only applies within an account (a PBX). I do not have a sub-account and extension dialing works fine.
azrobert:
I posted a detailed guide to setup a sub-pbx for an ObiON replacement and could be used for an IP phone.
See:
http://www.obitalk.com/forum/index.php?topic=5411.0
EDIT:
Since I posted the above guide I changed my sub-pbx config. I moved the Outbound CallerId from the sub-pbx to the extension. Before the change all traffic over the sub-pbx was assigned a CID of 4809999999. If you use the sub-pbx for only the IP phone then it doesn't matter where the CID is set.
Navigation
[0] Message Index
[#] Next page