OBi110 intermittently cannot make outgoing land line calls
bbiggs:
I bought an OBi110 a few months ago. I have set it up to use my land line as primary and a Google Voice line as secondary. I'm making sure the device itself works before I permanently port my land line to GV.
I was using the GV number as PRIMARY for a while, but I recently switched it back to use the land line as PRIMARY. Now, about 1 out of every 3-5 OUTGOING calls that I make rings ONE TIME and then gives me a whistle that the call can't be completed.
Also, when I have voice messages waiting on my land line, my phone's message waiting indicator does not flash.
My next step may be to do a factory reset on the device and start over with the configuration.
I'm not sure what else to do/check to get these things working. Any help is appreciated.
Jackson:
Did ya try to simply power cycle it?
dialbmay:
Quote from: bbiggs on June 02, 2013, 08:34:20 am
I bought an OBi110 a few months ago. I have set it up to use my land line as primary and a Google Voice line as secondary. I'm making sure the device itself works before I permanently port my land line to GV.
I was using the GV number as PRIMARY for a while, but I recently switched it back to use the land line as PRIMARY. Now, about 1 out of every 3-5 OUTGOING calls that I make rings ONE TIME and then gives me a whistle that the call can't be completed.
Also, when I have voice messages waiting on my land line, my phone's message waiting indicator does not flash.
My next step may be to do a factory reset on the device and start over with the configuration.
I'm not sure what else to do/check to get these things working. Any help is appreciated.
I never met your situation. I also bought one, earlier than you! But now it seems my luck is better.
Yet there have been no crash situation.
bbiggs:
Yes, I have cycled the power numerous times.
Here is the XML Call History for three calls I made this evening to the same number (I've replaced the actual number with asterisks).
Quote
<CallHistoryFile>
<CallHistory date="6/2/2013" time="21:57:30">
<Terminal id="PHONE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="21:57:30">New Call</Event>
<Event time="21:58:09">End Call</Event>
</Terminal>
<Terminal id="LINE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="21:57:35">Call Connected</Event>
</Terminal>
</CallHistory>
<CallHistory date="6/2/2013" time="21:43:18">
<Terminal id="PHONE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="21:43:18">New Call</Event>
</Terminal>
<Terminal id="LINE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="21:43:23">Call Connected</Event>
<Event time="21:43:44">End Call</Event>
</Terminal>
</CallHistory>
<CallHistory date="6/2/2013" time="20:17:19">
<Terminal id="PHONE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="20:17:19">New Call</Event>
<Event time="20:17:30">End Call</Event>
</Terminal>
<Terminal id="LINE1" dir="Outbound">
<Peer name="" number="*******"/>
<Event time="20:17:24">Call Connected</Event>
</Terminal>
</CallHistory>
The calls at 20:17:19 and 21:57:30 went through fine. It rang 3 or 4 times, the other end picked up, and then I hung up.
The call at 21:43:18 rang one time, and then I got 6 "busy beeps", followed by a disconnect. This looks like the call is disconnected on different sides (my side or the phone company).
I suppose it could be the phone company itself, but considering this line has been working flawlessly forever, that seems unlikely.
ianobi:
Try increasing Physical Interfaces > LINE Port > DialDelay from 500 to 1000. This increases the time taken after the OBi110 seizes the PSTN line to one second before it sends out DTMF digits. This gives the PSTN line time to settle and gives the local exchange equipment more time to be ready to receive the digits.
At default settings, the first burst of ringing you hear when dialling a PSTN call is sent to you by your OBi110 as some sort of "reassurance tone" while it is setting up the call. This can be confusing as most users assume it must be from the local Telco exchange.
Also at default settings, your OBi110 will always show "Call connected" in Call History whether or not the call has actually connected. This is due to the default setting:
Physical Interfaces > LINE Port > DetectOutboundConnectMethod: Assume connected after a short delay
Navigation
[0] Message Index
[#] Next page