HKBN 2B Obi110 or OBi100 settings
baor:
This post is intended to collect and share info on how to configure HKBN 2B in the Obi110 or Obi100.
I could get the device to register, but I will get an error message code "500" when I tried to dial out.
There is no ringing on my side when someone is calling me...
My router is Asus RT-N16. It is flashed with Tamagochi. I have forwarded 5060 and RTP ports in my router.
I have tried stun.xten.com and stun01.sipphone.com, stun.voipbuster.com, stun.ideasip.com.
I am using the following dial plan:
([2-9]xxxxxx|011xx.|1[2-9]xx[2-9]xxxxxx|<852:>[236789]xxxxxxxS0|[236789]xxxxxxxS0|1850xS0|188xS0)
My OBi110 is running 1.2.1 (Build: 2103).
Is there anyway we could have debug log for this device?
Could anyone help?
Thank you!
Below shows my settings:
Below shows the log
I tried to call a number as you could see the "OFF HOOK" Line
After dialing, an error message saying it is rejected by the service provider Code "500"
Thank you!!!!!!!!!!
<7> sendto cb505987:5060(842)
192.168.1.127 10/04 01:40:57.746
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:40:57.746
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:40:57.746
<7> TCP:Accept OK (HTTPD)
192.168.1.127 10/04 01:41:02.073
<145> Reboot is scheduled in 1 seconds
192.168.1.127 10/04 01:41:02.075
<7> TCP:Accept OK (HTTPD)
192.168.1.127 10/04 01:41:02.115
<7> TCP:Accept OK (HTTPD)
192.168.1.127 10/04 01:41:02.116
<0> Reboot checking..... 192.168.1.127 10/04 01:41:03.069
<143> Compare the version now
192.168.1.127 10/04 01:41:03.070
<0> Final Cleanup before reboot....
192.168.1.127 10/04 01:41:03.070
<144> Goodbye! Reboot Now. (reason: 9)
192.168.1.127 10/04 01:41:04.070
<6> ==== Networking is ready ====
192.168.1.127 10/04 01:41:10.274
<0> IP Address= 192.168.1.127 192.168.1.127 10/04 01:41:10.280
<0> Gateway = 192.168.1.1 192.168.1.127 10/04 01:41:10.281
<0> Netmask = 255.255.255.0 192.168.1.127 10/04 01:41:10.283
<3> SYSTEM REBOOTED (Reason: 9, lifecycle: 1496)
192.168.1.127 10/04 01:41:10.284
<0> SLIC_init ... 192.168.1.127 10/04 01:41:10.329
<0> Reset SLIC... 192.168.1.127 10/04 01:41:10.331
<150> Setup Provisioning for system start! 1200
192.168.1.127 10/04 01:41:10.342
<0> SLIC & DAA is initialized 192.168.1.127 10/04 01:41:12.000
<6> Start Main Service Now 192.168.1.127 10/04 01:41:14.052
<7> Voice Main
192.168.1.127 10/04 01:41:14.053
<7> [CPT] --- FXS s/w tone generator (0) ---
192.168.1.127 10/04 01:41:14.059
<7> BASESSL:load cert:5
192.168.1.127 10/04 01:41:14.162
<7> BASESSL:Load certificate ok
192.168.1.127 10/04 01:41:14.167
<7> sendto cb505987:5060(569)
192.168.1.127 10/04 01:41:14.452
<7> XMPP:Invalid cfg use for xmpp
192.168.1.127 10/04 01:41:14.453
<7> GTT:xmpp not configured
192.168.1.127 10/04 01:41:14.456
<7> XMPP:Invalid cfg use for xmpp
192.168.1.127 10/04 01:41:14.457
<7> GTT:xmpp not configured
192.168.1.127 10/04 01:41:14.458
<7> [SLIC] FAX MODE --- OFF
192.168.1.127 10/04 01:41:15.392
<7> [SLIC]:Slic#0 ON HOOK
192.168.1.127 10/04 01:41:15.394
<7> sendto cb505987:5060(569)
192.168.1.127 10/04 01:41:15.454
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.456
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.458
<7> sendto cb505987:5060(837)
192.168.1.127 10/04 01:41:15.472
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.743
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.761
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.801
<7> sendto cb505987:5060(285)
192.168.1.127 10/04 01:41:15.803
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:41:15.805
<7> [CPT] --- FXS s/w tone generator (7133) ---
192.168.1.127 10/04 01:41:21.194
<147> PROV: Auto Update invalid server name()
192.168.1.127 10/04 01:41:22.344
<7> [CPT] tone compression done - 12283 !!
192.168.1.127 10/04 01:41:26.342
<7> sendto cb505987:5060(843)
192.168.1.127 10/04 01:42:15.819
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:42:16.102
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:42:16.108
<7> [PR] prompt transcoding done!!
192.168.1.127 10/04 01:43:03.707
<7> [SLIC]:Slic#0 OFF HOOK
192.168.1.127 10/04 01:43:10.202
<7> [CPT] --- FXS SiLab h/w tone generator ---
192.168.1.127 10/04 01:43:10.203
<7> sendto cb505987:5060(843)
192.168.1.127 10/04 01:43:12.123
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:43:12.414
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:43:12.443
<7> [DSP]: ---- H/W DTMF ON (level:1) : * @ 119320 ms---- 192.168.1.127 10/04 01:43:13.373
<7> [DSP] ---- H/W DTMF OFF @ 119470 ms ---- 192.168.1.127 10/04 01:43:13.522
<7> [DSP]: ---- H/W DTMF ON (level:1) : * @ 119640 ms---- 192.168.1.127 10/04 01:43:13.693
<7> [DSP] ---- H/W DTMF OFF @ 119790 ms ---- 192.168.1.127 10/04 01:43:13.843
<7> [DSP]: ---- H/W DTMF ON (level:1) : 1 @ 120320 ms---- 192.168.1.127 10/04 01:43:14.373
<7> [DSP] ---- H/W DTMF OFF @ 120470 ms ---- 192.168.1.127 10/04 01:43:14.522
<7> [DSP]: ---- H/W DTMF ON (level:1) : 2 @ 122660 ms---- 192.168.1.127 10/04 01:43:16.712
<7> [DSP] ---- H/W DTMF OFF @ 122810 ms ---- 192.168.1.127 10/04 01:43:16.862
<7> [DSP]: ---- H/W DTMF ON (level:1) : 4 @ 123000 ms---- 192.168.1.127 10/04 01:43:17.052
<7> [DSP] ---- H/W DTMF OFF @ 123150 ms ---- 192.168.1.127 10/04 01:43:17.202
<7> [DSP]: ---- H/W DTMF ON (level:1) : 5 @ 123360 ms---- 192.168.1.127 10/04 01:43:17.412
<7> [DSP] ---- H/W DTMF OFF @ 123510 ms ---- 192.168.1.127 10/04 01:43:17.563
<7> [DSP]: ---- H/W DTMF ON (level:1) : 5 @ 123720 ms---- 192.168.1.127 10/04 01:43:17.772
<7> [DSP] ---- H/W DTMF OFF @ 123870 ms ---- 192.168.1.127 10/04 01:43:17.922
<7> [DSP]: ---- H/W DTMF ON (level:1) : 5 @ 124040 ms---- 192.168.1.127 10/04 01:43:18.092
<7> [DSP] ---- H/W DTMF OFF @ 124190 ms ---- 192.168.1.127 10/04 01:43:18.242
<7> [DSP]: ---- H/W DTMF ON (level:1) : 1 @ 124360 ms---- 192.168.1.127 10/04 01:43:18.412
<7> [DSP] ---- H/W DTMF OFF @ 124510 ms ---- 192.168.1.127 10/04 01:43:18.562
<7> [DSP]: ---- H/W DTMF ON (level:1) : 2 @ 124650 ms---- 192.168.1.127 10/04 01:43:18.703
<7> [DSP] ---- H/W DTMF OFF @ 124810 ms ---- 192.168.1.127 10/04 01:43:18.862
<7> [DSP]: ---- H/W DTMF ON (level:1) : 6 @ 125040 ms---- 192.168.1.127 10/04 01:43:19.092
<7> [DSP] ---- H/W DTMF OFF @ 125190 ms ---- 192.168.1.127 10/04 01:43:19.243
<7> [DSP]: ---- H/W DTMF ON (level:3) : # @ 125480 ms---- 192.168.1.127 10/04 01:43:19.532
<7> [DSP] ---- H/W DTMF OFF @ 125610 ms ---- 192.168.1.127 10/04 01:43:19.663
<142> PARAM Cache Write Back(256 bytes) 192.168.1.127 10/04 01:43:20.084
<7> STUNC:ERR=TO,mtd=1
192.168.1.127 10/04 01:43:58.754
<7> sendto cb505987:5060(952)
192.168.1.127 10/04 01:43:58.757
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:43:59.038
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:43:59.043
<7> sendto cb505987:5060(358)
192.168.1.127 10/04 01:43:59.044
<7> RTP:Del Channel
192.168.1.127 10/04 01:43:59.046
<7> [CPT] --- FXS SiLab h/w tone generator ---
192.168.1.127 10/04 01:43:59.055
<7> [CPT] --- FXS s/w tone generator (165005) ---
192.168.1.127 10/04 01:43:59.056
<7> sendto cb505987:5060(843)
192.168.1.127 10/04 01:44:12.460
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:44:12.752
<7> RxFrom:cb505987:5060
192.168.1.127 10/04 01:44:12.756
<7> [SLIC] FAX MODE --- OFF
192.168.1.127 10/04 01:44:17.540
<7> [SLIC]:Slic#0 ONHOOK
192.168.1.127 10/04 01:44:17.541
<7> [SLIC]:Slic#0 OFF HOOK
192.168.1.127 10/04 01:44:21.740
<7> [CPT] --- FXS SiLab h/w tone generator ---
192.168.1.127 10/04 01:44:21.742
____________________________________________________________
2011-04-11
We finally made some progress after OBIHAI Support suggested to turn off X_InsertRemotePartyID.
I could receive call and dial out. However I got cut off every 10 mins.
Does it have to do with X_KeepAliveExpires or RegistrationPeriod?
obi-support2:
baor,
1. What kind of home router you have?
You can check whether the router has a SIP ALG function.
If it has, try TURNING OFF the feature and call again.
2. Make sure the number you try to call is acceptable by HKBN.
Have you tried to call the same number from another
device or softphone with HKBN? and successful?
3. We can also check your device configuration remotely. For privacy you can
email support@obihai.com and provide your OBi number (printed on the back of the unit),
and we can provide you further assistance.
RonR:
SIP error code 500 is : Internal Server Error.
You have a STUN server configured : stun01.sipphone.com
This STUN server was shut down a couple of weeks ago and will not return. Unless the current firmware has changed the timeout, you will experience a 40 second delay on each call you attempt with a non-existent STUN server.
yhfung:
In fact I am one of HKBN 2b users in Hong Kong. I have been able to install it in my SPA3000, PAP2T and Asterisk server. The settings of HKBN 2b is given by
http://www.hkepc.com/forum/viewthread.php?tid=1141462&page=218#pid18904520
I have already tried several times to register the 2b server with my OBi110 in Shenzhen but still failed. I believe the information provided in the above link should provide a good reference of how to convert the settings in Linksys SPA to OBi devices.
YH
yhfung:
I just reconnected my old Linksys PAP2T ATA with the HKBN 2b settings in LINE 1 tab. The HKBN 2b settings in the PAP2T works very well. It can make HK PSTN outbound call and receive HK PSTN call with caller ID shown on the phone attached to it.
My network configuration is shown as follows:
Interent --> China Telecom --> modem --> Router (Draytek 2200E Plus) --> i) PCs, ii) Asterisk, iii) SPA devices including SPA941, PAP2T, iv) OBi110.
Based on the information shown in the above post, the PAP2T, configured to connect HKBN 2b server, can make and receive call without any problem encounter. Please note that I do not need to set any UDP ports forwarding (5060 and RTP number range) to my PAP2T.
Also based on my pass experience of using Linksys ATA, the settings for HKBN 2b in PAP2T which can make the SIP client be visible from the WAN port. That's to say that the SIP client looks like sitting in the fornt of the WAN port of the router.
So back to the OBi110 or OBi100, how can we make the internal SIP client (behind router) be in front of the WAN port of the router although it is connected to the LAN port of the router?
YH
Navigation
[0] Message Index
[#] Next page