NEED HELP CONNECTING (2) OBI110 FOR REMOTE PAGING ACCESS
Shale:
Quote
"The OBi paging method seem to work better I could call OBi110 #2 call is picked up automatically. after page tone, I was able to get intercom dial tone from Simplex PA system and dial Simplex feature code and access paging feature. The only problem under this scenario when I would hang up the phone the Simplex PA system would remain off hook and waiting for disconnect signal."
I was interpreting that to say the big problem now was to get the PA to realize the call was done.
ianobi:
Shale,
The problem is if the OBi is in paging mode, then the OBi Phone Port stays off hook all the time, it will never give a disconnect signal.
Using the Line Port with the OBi not in paging mode should work fine as described in my simulation. When #1 OBi hangs up it will release the call through #2 OBi to the PA.
miteldavid:
QBzappy,
I tried setting up On the OBi2 DTMF to 'inband' (Service Providers->ITSP Profile X->General->DTMFMethod). also tried playing around DTMF settings with no success But with same results. I can call from Obi1 and monitor line at OBi2 and hear a ring, tone or voltage that breaks loop on Simplex PA system then connected to line. At stage no intercom dial tone and Simplex PA system in dumb mode waiting. Caller on OBi1 hears one ring and OBi2 picks up and silence. begin to dial simplex access code and get error tone from simplex PA system. Its is connecting to Simplex but something when the OBi 2 is called that ring, tone or voltage on the line port is setting off Simplex before being connected. If I could get rid of that little tone this setup would be working. Thanks for all efforts!
Ianobi,
call history report on OBI1.
Call 1--------------- 08/21/2013-----12:13:08----------
Terminal ID ----------PHONE1 -------------------------SP2
Peer Name --------- blank ----------------------------blank
Peer Number---------100-------------------------------av@10.100.11.5:5061
Direction------------ Outbound------------------------ Outbound
12:13:08------------ New Call--------------------------blank
12:13:11 -----------blank------------------------------Call Connected
12:13:19------------ End Call---------------------------blank
call history report for OBi2
Call 1 --------------------08/21/2013-------12:42:35 ----------
Terminal ID ---------------SP2---------------------------------- LINE1
peer Name ---------------blank---------------------------------blank
Peer Number --------------district -------------------------------av
Direction ------------------Inbound ------------------------------Outbound
12:42:35 ------------------Ringing ------------------------------blan
12:42:38-------------------blank ------------------------------Call Connected
12:42:53 ------------------End Call------------------------------blank
I programmed hotline setup. Same results. I used a simple set up from a post I read! but maybe there is somthing wrong with this set up and should be using your set up caonfig! Thanks for all efforts!
For Hotline
On both OBi110s:
Replace Physical Interfaces -> Phone port -> DigitMap:
(<S0:100>)
On OBi110#1:
Replace Physical Interfaces -> Phone port -> OutboundCallRoute:
{100:sp2(av@10.100.11.5:5061)}
On OBi110#2:
Replace Physical Interfaces -> Phone port -> OutboundCallRoute:
{100:sp2(anything@10.5.1.6:5061)}
ianobi:
Take a leap of faith and use my config from reply #6. I have tried it and it works. The problem with the configs you are trying is that instead of simply seizing the #2 OBi line port, you are sending digits / tones through the port as you seize it.
Mostly the setup is ok. You just need to send nothing! That way you will get the PA dial tone.
It's getting late in my time zone - I'm hoping for good news in the next 30 mins or maybe in the morning :)
If it works as it does for me it is instant, so you pick up #1 OBi phone and get dial tone. The only way to prove it is PA dial tone is to dial digits and see if it works.
Edit: To give it the best chance use:
#2 OBi
Voice Services -> SP2 Service -> X_InboundCallRoute:
{li}
We can build in the security later.
QBZappy:
miteldavid
Dialing '#' first seems to me like a false positive. This by passes the OBi and talks directly to the PA system. I don't think David has succeeded in dialing using the phone attached to the OBi2 directly. Until he succeeds on this leg, I suspect that the OB1=>OBi2 leg of the trip will not work.
Navigation
[0] Message Index
[#] Next page
[*] Previous page