10 digit dialing on SP1 & 11 digit dialing on SP2
threehappypenguins:
I don't really understand what I'm doing, and I can only copy and paste (that is to the extent of my understanding).
What would I do in the expert config that I can make the dialing rules to be 10 digit dialing on SP1 & 11 digit dialing on SP2?
Shale:
My original always puts leading 1 for 10-digit numbers. Your starting point may differ:
(933|*xx|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.)
ISTP Profile A General: DigitMap
Modified to always only put 10 digit dialing:
(933|*xx|<1:>xxxxxxxxxx|[2-9]xxxxxxxxx|011xx.|xx.)
ISTP Profile A General: DigitMap is probably already set to use 11- digits out.
So if the 1 is dialed followed by 10 more digits, delete the 1. If 10 digits are dialed that don't start with 1, pass it through without adding a 1.
If the above is not sufficient, paste a copy of the existing values of the strings you currently have that you propose to modify.
If you want to discuss strings you see in other posts, it would be better that you reply to the post that has the string that you intend to copy from. In other words, the prelude to what is in your head is handy to the person.
If you are asking how to make the fact that a 1 was dialed initially be OBi's indicator as to whether to use SP1 or SP2, say so.
On the other hand, if you are asking how to generically put a value into expert mode, then see the sticky thread in that describes this: OBiTALK Community > General Support > OBiTALK Web Portal > OBi Expert Configuration (Introduction) http://www.obitalk.com/forum/index.php?action=post;topic=6493.0;num_replies=0
threehappypenguins:
Quote from: Shale on August 19, 2013, 09:44:00 am
If you are asking how to make the fact that a 1 was dialed initially be OBi's indicator as to whether to use SP1 or SP2, say so.
Yes. SP1 is Freephoneline and SP2 is Google Voice. I want it set up (this is all for my sister, btw) so that when a 1 is dialed it will go to SP2. Otherwise, 10 digits will simply go to Freephoneline SP1.
I am assuming I would put a string into the digitmap in ITSP Profile A? Or would I need to do something to the phone port DigitMap & OutboundCallRoute too?
Shale:
Correction....
To summarize, you want to send all 11 digit numbers starting with 1 to SP2, and 10 digits not starting with 1 will go to Freephone SP1. It is OK if the 1 is prepended to the numbers before sending the number with Freephone.
That will be more complex than what I thought most probable initially, and you will have to modify phone port strings to route the dialed call to the desired SP.
I suggest you post your phone port OutboundCallRoute, phone port DigitMap and your ISTP Profile A General: DigitMap , and your ISTP Profile B General: DigitMap
Somebody will probably post suggested things based on those.
threehappypenguins:
These are the current settings (they are default):
ITSP Profile A Digitmap: (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)
ITSP Profile B Digitmap: (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)
Phone Port Digitmap: ([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**9(Mpp)|(Mpli))
Phone Port OutboundCallRoute: {([1-9]x?*(Mpli)):pp},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Navigation
[0] Message Index
[#] Next page