Getting a UK PSTN line to work with OBI110
jrinco11:
perhaps this belongs in a different thread now, but how would I go about getting numbers dialed starting with a 0 (ie, 0xxxxxxxxxx) to be routed through the LINE port and any other international or US local (1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|01144xxxxxxxxxxx|011xx.|(Mipd)|[^*]@@.) go to SP1, with out, for example, having to dial **8 to get to the LINE port to dial local UK numbers?
EDIT: ah .. I need to edit the "Setup Wizard"->"Phone OutboundCallRoute" to handle this...trying now..
EDIT 2: okay, so I got it working to when I dial local UK numbers it uses the LINE port and for any US or other Int'l numbers it uses the primary line (SP1 which is GV). However, when I dial a local UK number, it takes about 8 seconds before the call actually connects. I dial a number, wait about 12 seconds, I get a single US ring tone, it sounds like it hangs up, wait another 5 seconds, and then I start getting a UK ring tone (and the call starts ringing the number I dialed).
I simply added the Mli digitmap to the front of my outbound route, and for the LINE digitmap, I just placed (0xxxxxxxxxxx) to match UK numbers:
outbound route before: {([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
outbound route now: {(Mli):li},{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):pli}
physical interface -> line -> digit map: (0xxxxxxxxxx)
any suggestions?
LeftRight:
One option to call out on your LINE port is to: Press #, hear dial tone from PSTN, then dial your local UK number.
If you choose * * 8 for dialing out on LINE port, then, OBi takes some extra time to send the digits out to the PSTN, which could include (after you finish dialing the number):
1/ digit map timeout (2 seconds), changeable in the LINE port DigitMap
2/ Dial delay (500 ms by default)
3/ re-generate DTMF digits, each digit takes 400 ms by default (200 ms ON, 200 OFF).
4/ Extra delay after sending out all digits before OBi passes audio over (2 seconds)
Also, you may press a terminating # at the end of dialing an international number. You can also modify LINE port DigitMap to reduce the timeout if amount of digits are known for international number.
(1), (2), (3) are all changeable in OBi settings, and you may get help from OBi support on this ...
jrinco11:
hmm, I'm still getting random issues where I'll pick up an incoming call from the LINE port and it will be dial tone (as if the call instantly disconnects). Perhaps now that the obi110 is sold on amazon.co.uk, someone has the ability to list all the settings pertaining to the phone/line port on a UK version of the obi110?
jrinco11:
would it be possible to get a full list of correct UK settings for the obi110? I've purchased a new land line phone and now I am unable to get a dialtone, or incoming calls (however, when plugged directly into the pstn line - not through the obi110 - the phone works fine). Perhaps I could import the settings from a uk-sold obi110?
mrbenjaminjo:
I'm having trouble with inbound UK PSTN.
Test scenarios:
-Phone LED lit
-Line LED lit
-Inbound SIP causes phone on phone port to ring.
-Outbound SIP call works.
-Outbound PSTN call works.
-# gets PSTN line dial tone, line LED flashes, outbound works.
-Power off to OBI PSTN pass-through works, phone rings.
-Phone connected direct to PSTN, phone rings.
-PSTN inbound, line LED does not flash, phone does not ring (call history blank)
-PSTN inbound, dial # to connect to PSTN call, picks up inbound (call history logs call)
-Phone & Line Status show correct lastcallerinfo for Line Port Status, even though phone does not ring.
Basically the Obi isn't seeing the PSTN line ring, and I'm pretty sure that everything above points at a config issue (perhaps ring detection?)
I'm configuring the device directly.
Thanks for any help you can offer!
Ben.
Navigation
[0] Message Index
[#] Next page
[*] Previous page