Anveo - outbound CallerID for SIP to SIP calls
ipse:
Apologies if this was answered here before and I missed it, but I'd like to know if the Outbound CallerID info I populated in my Anveo "SIP Device Registration" page is supposed to work with SIP to SIP calls.
It doesn't at the moment - it works however on SIP-PSTN calls.
As it stands, the CallerID is sent as the Anveo username - which makes little sense for the called party.
I have an Obi110 as my ATA, but don't think there is anything I can set in there to change what Anveo sends out - at least I did not find a way.
Cheers...and BTW, I posted this on dslreports as well, didn't get a clarification yet.
giqcass:
I don't know if this will do it but I think Anveo supports it for sip to sip calls. Even then it might get tossed out by the receiving party. On the Obi try the following. ITSP Profile X and SPX refer to the Sip Profile and Service provider Anveo is using.
Service Provider>>>
>>>>>>>>>>>>>ITSP Profile X
>>>>>>>>>>>>>>>>>>>>>>>SIP
>>>>>>>>>>>>>>>>>>>>>>>>>>X_SpoofCallerID =checked
Voice Services>>>
>>>>>>>>>>>>>SPX
>>>>>>>>>>>>>>>>CallerIDName
ipse:
Thanks giqcass...I had these 3 settings set the way you suggested but as I said, it didn't work :(
Interesting, when the other party calls me (Callcentric->Anveo, SIP-to-SIP, Obi to Obi) I see their CC 1777 number AND the Caller Name.
Could this have anything to do with me being in Canada and the 2 providers in US (different CNAM handling)? But then again, my buddy is in Canada too....
Obviously not a big deal, but I admit getting lost in CallerID and CNAM manipulations with VoIP.
hwittenb:
If you are calling a sip uri from the OBi110 Anveo doesn't send the call, the OBi110 sends the call. The OBi110 pulls the caller id from the userid you have setup under the SPx UserID field, or if a Gateway it pulls the caller id from the AuthID field in the Gateway.
If you are calling using a SpeedDial then the OBi also has a format to introduce a userid ... ;ui=19251234567 ... See Enhancements & Fixes in Maintenance Release 1.2.1(2283)
http://www.obitalk.com/forum/index.php?topic=9.0
ipse:
Quote from: hwittenb on January 03, 2014, 10:15:03 am
If you are calling a sip uri from the OBi110 Anveo doesn't send the call, the OBi110 sends the call. The OBi110 pulls the caller id from the userid you have setup under the SPx UserID field, or if a Gateway it pulls the caller id from the AuthID field in the Gateway.
If you are calling using a SpeedDial then the OBi also has a format to introduce a userid ... ;ui=19251234567 ... See Enhancements & Fixes in Maintenance Release 1.2.1(2283)
http://www.obitalk.com/forum/index.php?topic=9.0
That IS sweet...thanks for the tip...I actually DO use a speed dial entry for this.
/EDIT: No dice...
Interestingly, when I set the speedial entry xx=SP2(1777xxxxxxxx@in.callcentric.com;ui=1234) the called party sees an anonymous call (no callerID sent)
When I configure xx=SP2(1777xxxxxxxx@in.callcentric.com;user=1234), the CallerID is the Anveo account name, same as without the option.
I wonder if this is the place to force a change - as this is mainly designed for NAT traversal (it's been a while since I looked into SIP+NAT).
Navigation
[0] Message Index
[#] Next page