InboundCallRoute Explained
azrobert:
Try This:
In CSipsimple select Accounts
Select Add Account.
Choose BASIC Wizard
Account name = anything
User = userid2
Server = 192.168.1.100:5061
Password = anything
SAVE
Press and hold on the account name.
When a new screen appears, select "Choose Wizard".
Select Expert Wizard
Select your account again by tapping name.
Select Registration URI and blank it out, then ok.
SAVE.
192.168.1.100:5061 is your OBi IP address and port.
Use the CSipSimple dialer to make calls.
pvpham:
I can make call from cell #2 using both Native and CSipSimple dialer using Sip2Sip account . However I do not know if it works to my intention which is to be able to make call thru GV or phone plan at my choosing. It always work because cell phone #2 has a phone plan. Sip2Sip account history does not show anything. I do not know how to verify that the call I made is thru the phone plan or thru OBi>GV
Also when call made to GV(sp1) cell phone #2 won't ring.
Here what I did:
SP2 :
X_InboundCallRout: {pvpham|userID2>(Msp1):sp1},{101|102>17771234567:aa},{ph}
pvpham is Sip2Sip account of 1st cell phone ( no phone plan)
userid2 is Sip2Sip account of 2nd cell phone( has phone plan with PagePlus)
101 is extension of Callcentric for cell phone 1
102 is extension of Callcentric for cell phone 2
CsipSimple: add account with Callcentric for 102, add account with Sip2Sip per your instruction for userID2
SP1:
X InboundCallRout: {ph,sp2(17771234567101|17771234567102@in.callcentric.com;ui=$1)}
azrobert:
Did you setup cell#2 with my Reply#15 instructions?
Do you have a data plan on cell#2 or do you have a plan for only calling?
If you have a data plan on cell#2, when you are out of the house do you want to use the data plan to make calls using the OBi100?
My reply#15 instructions do not use Sip2Sip and will only work on your local WiFi network.
If you want to use your data plan on Cell#2, you must use the previous instructions with the filter.
azrobert:
Check the OBi100's call history to make sure Cell minutes are not used.
Log directly into the OBi100 using the Web interface.
Go to Status -> Call History
SP1 X InboundCallRoute: {ph,sp2(17771234567101@in.callcentric.com;ui=$1) ,sp2(17771234567102@in.callcentric.com;ui=$1)}
PCHudd:
Hi. I've been using an OBi 110 with Google Voice for a couple of years with just a basic config. However, now that Google is ending XMPP support, I have started to look at doing more with the OBi. I currently have it configured with Google Voice on sp1 and Callcentric on sp2.
My question concerns making changes to X_InboundCallRoute on the sp2 voice service. Currently this is configured as follows:
{(x.1nnnnnnnnnn):aa},{>17771234567:ph} ----> where 1nnnnnnnnnn is my mobile number. (This is how I found it when I went to modify the config for the first time.)
I read azrobert's posts on how to configure the inbound call routing so that my Callcentric sub-account can access the OBi's auto attendant. I changed my X_InboundCallRoute to this:
{101>17771234567:aa},{ph}
As instructed, I submitted the change and rebooted the OBi. It worked the first time I tried it, but then the OBi automatically reset X_InboundCallRoute back to {(x.1nnnnnnnnnn):aa},{>17771234567:ph} after a few minutes. I tried this again several times with the same result. Finally, I made the change, submitted, rebooted and waited for about a minute without attempting a call. Sure enough, the config had reset itself again.
Has anyone else experienced this? Am I missing something? Forgive me for being a noob. I have a background in networking from years ago, but sip and voip are new to me. Any help would be appreciated. Thanks.
Navigation
[0] Message Index
[#] Next page
[*] Previous page