Yealink T-22P with Obi110

(1/4) > >>

ikonos:
I am trying to configure Yealink T-22P IP phone to work with Obi110 to call out PSTN or Voip provider. Reading through some of the posts I was able to setup an Analog phone connected to Obi110 Phone Port and Zoiper on my PC connecting to Obi110 call out through the PSTN connection on the line port or the Voip provider configured on SP1. I was also able to setup incoming calls ringing both phones.

I got an Yealink phone to replace the Zoiper and am struggling to configure it to talk to Obi110. Couple of posts indicate they were able to do it but did not provide any details. I do not want to use pbxes.org sub account or other means to achieve it.

I am trying to point Yealink to SP1 by providing Obi IP address and port number. I configured obi side using http://www.obitalk.com/forum/index.php?topic=2454.0 (This are the same settings I used succesfully with Zoiper). Can any one suggest me how I can configure yealink phones?

Thanks
Ik.

azrobert:
I helped someone with a Yealink T46 here:
http://www.obitalk.com/forum/index.php?topic=7323.0

Edit:

The above thread is a setup for only the Line Port for the Yealink.

If you want it to access an SP provider use must use a prefix. I use a "9" prefix instead of **8 to route calls out the Line Port. I don't know how you setup the Phone Port to access the Line Port, so if I included a suggestion it might affect how you are using the Phone Port.

ikonos:
Quote from: azrobert on March 25, 2014, 08:15:49 pm

I helped someone with a Yealink T46 here:
http://www.obitalk.com/forum/index.php?topic=7323.0


I did go through that post few days back when I was considering whether to buy yealink or cisco phone and decided on yealink with the understanding some one go it to work. I guess I will read through it again thoroughly and see what I am doing wrong. Thanks.

azrobert:
Check my update.

ikonos:
I just read through your post again. I have Obi100 at home with GV on SP1 and Anveo on SP2 and Obi110 at work with PSTN on line port and Anveo on SP1. I am testing currently with Obi100. Since I followed Single Stage Dialing instructions from the link I mentioned earlier, I setup tsc as user defined setting and added the IP address of yealink as one of the userid. (I tried actual userid as well before).


My settings below.

Default DigitMap for both ITSP A and B.
User Defined Digit Maps is set to ipd (defaults), tsc and p2p as follows.

tsc: (UserId1|Ip1)
p2p: ()

X_inboundCallRoute on SP1
{ph}

X_inboundCallRoute on SP2
{(Mtsc)>(<*1:>(Msp1)),(Mtsc)>(<**1:>(Msp1)):sp1},{(Mtsc)>(Mp2p):sp1},{(Mtsc)>(Mtg1):tg1},{(Mtsc)>0:ph},{(Mtsc):},{ph}

PhonePort DigitMap
(<P2P>(Mp2p)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**9(Mpp))

PhonePort Outbound Call Route
{(P2P:>@@.):sp1},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**9:>(Mpp)):pp}

Navigation

[0] Message Index

[#] Next page