CircleNet would like to introduce ourselves to the Obi world
dial.tone:
How do you configure your OBI?
I use the web interface (192.168.x.x).
Do you use Callcentric for outbound calls, or just inbound calls?
I use Callcentric for inbound calls. I use CircleNet via Voice Gateway for outbound calls.
What SP trunk is Callcentric defined on?
Callcentric is defined on SP1 (for line 1 going into my 2-line deskphone).
Callcentric is defined on SP2 (for line 2 and the fax machine).
What is your Primary Line?
Phone1 and Phone2, both, are set to SP1 Service. I'm redirecting Phone2 to SP2 Service at this time.
I have tried to make the simultaneous digitmap changes to all 4 setups (SP1, SP2, VG1, and VG2), but I may have missed one. I'll go back and doublecheck to make sure the digitmaps are as follows:
Service Providers -> ITSP Profile A and B -> General:
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|011xx.S3|(Mipd))
Voice Services -> Gateways and Trunk Groups -> Voice Gateway1 and 2:
(1xxxxxxxxxx|011xx.S3|<1919>xxxxxxx)
And I'll make sure the Primary Line on Phone 2 is set to SP2 Service. Does that all sound right?
Edit 1:
Ok, here are the results. With Service Providers -> ITSP Profile A and B -> General -> Digitmap set as follows:
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|011xx.) -- Result, circuit busy after 5 seconds
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|011xx.|(Mipd)|[^*#]@@.) -- Result, circuit busy after dialing 1st digit
(*xx.|**275*x.|[3469]11|1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.) -- Result, 12-second delay but call went through
azrobert:
Change the Phone Port DigitMap to this:
((Mvg1)|[1-9]x?*(Mpli)|[1-9]|[1-9][0-9]|911|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))
Make sure OBItalk provisioning is Disabled.
dial.tone:
Quote from: azrobert on April 25, 2014, 11:01:09 am
Change the Phone Port DigitMap to this:
((Mvg1)|[1-9]x?*(Mpli)|[1-9]|[1-9][0-9]|911|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))
Make sure OBItalk provisioning is Disabled.
Prepare yourself for the Knighthood Ceremony, Sir azrobert!! You are truly a genius! Delay is gone. Now I don't have to endure that just-call-AT&T look from my wife tonight!! She will probably send you a Christmas card this year!
Sam_from_CircleNet:
dial.tone I think I owe azrobert more than a card :-),
Also there is a chance your wife might be right about ATT, we do terminate some traffic using their network.
Sam Moats
zorlac:
Quote from: azrobert on April 25, 2014, 11:01:09 am
Change the Phone Port DigitMap to this:
((Mvg1)|[1-9]x?*(Mpli)|[1-9]|[1-9][0-9]|911|**0|***|#|##|**70(Mli)|**8(Mbt)|**81(Mbt)|**82(Mbt2)|**1(Msp1)|**2(Msp2)|**3(Msp3)|**4(Msp4)|**9(Mpp)|(Mpli))
Make sure OBItalk provisioning is Disabled.
Is that all one string into that first field?
Would that string be OK for circlenet on SP2?
Thanks again!
OK this config works (on my obi100) but there is a ~13sec ring pause. :(
DigitMap: ([1-9]x?*(Mpli)|[1-9]S9|[1-9][0-9]S9|911|**0|***|#|**1(Msp1)|**2(Msp2)|**9(Mpp)|(Mpli))
OutboundCallRoute: {(Mvg1):vg1},{([1-9]x?*(Mpli)):pp},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**9:>(Mpp)):pp},{(Mpli):pli}
Navigation
[0] Message Index
[#] Next page
[*] Previous page