CircleNet would like to introduce ourselves to the Obi world
lottamoxie:
Hi Circlenet!
I've just signed up to try out your service.
I am unable to get my Obi device to successfully connect to your service. I followed your directions on your site.
I'm getting "backing off...authentication" errors.
Anyway, I put in a ticket already today. Can you assist me?
Thanks!
Sam_from_CircleNet:
Hi Lottamoxie,
I think we know which ticket is yours and you should have a response to it by now. If you are who I think you are we are receiving your registration but it appears we are getting a blank password from your Obi. I've sent your password in the response to the ticket I didn't want to put it here. Please try putting the password we sent you in the ticket into your obi profile and let us know if it works.
Thanks,
Sam
BTW: The obi has a lot more features and flexibility than the Linksys ATA but with the added features comes an increase in complexity. We do support the other device also if you'd like config help on that open a ticket with us I'd like to keep my forum posts here Obi centric.
lottamoxie:
Well now it's showing "registered." :-D
I am still using Google on my SP1 until May 15th when GV with Obi goes kaput. Then I will use a DID number on SP1 and continue to use Circlenet.us on my SP2 for outbound calls.
Thank you for your rapid response. I look forward to trying out your service.
ETA: I just made an outbound call using circlenet.us. I only ever call in the US. Call quality was excellent! A just under 5 min call to FL was 0.021. I'm pleased!
voiper1:
Quote from: azrobert on April 27, 2014, 12:11:27 am
voiper1,
The config looks good to me.
Check the OBi100 Call history to see where the call is going and the number sent.
Log into the OBi via the Web interface.
Click Status
Click Call History
The following will eliminate any long pause and won't fix your problem unless you're doing something weird.
ITSP Profile A -> DigitMap:
(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xxxxxx.S3)
If you configure the OBi100 via the web interface check:
System Management => Auto Provisioning
Under OBiTalk Provisioning:
Method must be Disabled.
Thank you azrobert.
I did already have that pattern in place. Yes I also cleared that auto provision thing per your mention in previous posts. The delay is not a big issue but it seems like it comes and goes. I am not concerned. The static might have been there in the past, but I can't remember. Sam did say it should go away when it connects but calling my cell phone I still get it. It could be just parasitic noise from several things I realize and not even related to the connection but the jacks and obi and such. As a side not my OBI 100 over heated back in December and November. Being an electronics engineer sadly not having any heatsinks on hand I just took the cover off the OBI and let it free air and it seems to help. A new one or a heat sink would fix it I know. Ah well.
Sam has been very helpful and so far so good. If you are like me and could spend $30 on Vestalink or 35 on PowerPhone but 1) I dont like limited even though I hardly use my VOIP line, and 2) If I can get it pay as you go low cost I am in. Who wants to pay the man/women for time I dont use?
So far I have my time invested and that is all. Callcentric incoming NY number.. and CircleNet is a winner. NO brainer just follow this forum and should be easy to get you setup if you at all have a tech nerve in your body.
Thanks again forum. I will update as i use the phone more and give feedback. ;)
voiper1:
HI azrobert and Sam, I noticed *67 caller ID blocking is not working calling out on CircleNet, is there something I need to do in the OBI or online interface? Or is it even possible?
By the way I noticed I had the volume up on the handset and I think that is why the sudden mild static on the line. Through all this testing I somehow cranked up the volume by accident.
Thanks..
:)
Navigation
[0] Message Index
[#] Next page
[*] Previous page