CircleNet would like to introduce ourselves to the Obi world
azrobert:
Quote from: Jumbo on April 18, 2014, 07:03:18 am
Quick followup question on this.. if CallCentric is registered as SP2 and if I want to use CircleNet as outbound on SP2, what changes do I need to make?
Appreciate the help, thanks!
You can share an SP trunk with 2 services by using a Voice Gateway.
Voice Gateways are used with outbound only providers that don't need to register.
CircleNet fits this category.
Keep GV on SP1.
Define Callcentric on SP2
Define CircleNet on Voice Gateway 1:
Voice Services -> Gateways and Trunk Groups -> Voice Gateway1
Name: CircleNet
AccessNumber: sp2(outbound.circlenet.us)
DigitMap: (<8:>1xxxxxxxxxx|<8:1>xxxxxxxxxx|<8:1aaa>xxxxxxx|<8:>011xxxxxx.S3)
AuthUserID: Your_CircleNet_ID (10 digit ID)
AuthPasssword: Your_CircleNet_Password
aaa is your local area code. This is used for 7 digit dialing.
Add to the beginning of the Phone Port OutboundCallRute:
{(Mvg1):vg1},
Continue to use GV as you are currently.
To use CircleNet dial as follows:
814805551212 or
84805551212 or
85551212 or
8011............
After May 15th change the Voice Gateway DigitMap to:
(1xxxxxxxxxx|<1>xxxxxxxxxx|<1aaa>xxxxxxx|011xxxxxx.S3)
Dial without the "8" prefix to use CircleNet.
siskiou:
Quote from: azrobert on April 17, 2014, 08:04:53 pm
To route tollfree and international calls to SP2
Change Service Providers -> ITSP Profile B -> DigitMap To:
(18(00|88|77|66|55|44)xxxxxxx|011xxxxx.S3)
Add to the beginning of Physical Interfaces -> Phone Port -> OutboundCallRoute:
{(Msp2):sp2},
Since CircleNet is outbound only, registration is not required.
Unregistering will reduce traffic to the CircleNet servers.
Voice Services -> SP 2 Service -> X_RegisterEnable: Unchecked
Hi, thanks very much for the instructions. I've followed them, but when I tried with a toll free number, it was still routed through SP1. Did I miss something?
Edited to add: when I checked the Obi settings, I found that they didn't "stick", despite rebooting. I'll try again...
And now it works perfectly! Thanks very much!
siskiou:
Quote from: Sam_from_CircleNet on April 18, 2014, 01:55:49 am
First, welcome aboard siskiou I'm glad your doing ok and thanks to the OBITalk forum for helping out my customer!
Secondly, the advice given by azrobert is good we do use 011 to denote international calls and this setup should work.
Thanks! I placed my first call to Germany, and call quality was excellent! Much better than GV!
Jumbo:
Thanks a bunch! That did it. azrobert, you truly are a hero member.
Quote from: azrobert on April 18, 2014, 10:11:47 am
Quote from: Jumbo on April 18, 2014, 07:03:18 am
Quick followup question on this.. if CallCentric is registered as SP2 and if I want to use CircleNet as outbound on SP2, what changes do I need to make?
Appreciate the help, thanks!
You can share an SP trunk with 2 services by using a Voice Gateway.
Voice Gateways are used with outbound only providers that don't need to register.
CircleNet fits this category.
Keep GV on SP1.
Define Callcentric on SP2
Define CircleNet on Voice Gateway 1:
Voice Services -> Gateways and Trunk Groups -> Voice Gateway1
Name: CircleNet
AccessNumber: sp2(outbound.circlenet.us)
DigitMap: (<8:>1xxxxxxxxxx|<8:1>xxxxxxxxxx|<8:1aaa>xxxxxxx|<8:>011xxxxxx.S3)
AuthUserID: Your_CircleNet_ID (10 digit ID)
AuthPasssword: Your_CircleNet_Password
aaa is your local area code. This is used for 7 digit dialing.
Add to the beginning of the Phone Port OutboundCallRute:
{(Mvg1):vg1},
Continue to use GV as you are currently.
To use CircleNet dial as follows:
814805551212 or
84805551212 or
85551212 or
8011............
After May 15th change the Voice Gateway DigitMap to:
(1xxxxxxxxxx|<1>xxxxxxxxxx|<1aaa>xxxxxxx|011xxxxxx.S3)
Dial without the "8" prefix to use CircleNet.
azrobert:
Quote from: siskiou on April 18, 2014, 10:21:55 am
Edited to add: when I checked the Obi settings, I found that they didn't "stick", despite rebooting. I'll try again...
If you are configuring your OBi from the Web interface, you need to disable OBiTalk provisioning. If you don't disable provisioning, OBiTalk will overlay your changes.
System Management -> Auto Provisioning -> OBiTalk Provisioning -> Method: Disabled
Make sure you are changing the Method under OBiTalk Provisioning.
Navigation
[0] Message Index
[#] Next page
[*] Previous page