CircleNet would like to introduce ourselves to the Obi world
azrobert:
First, check my Reply#64 in this thread about provisioning.
The inbound call route is where you direct calls to phone1 or phone2.
Voice Services -> SP1/2/3/4 Service -> X_InboundCallRoute:
ph
or
ph2
If you have more than 1 rule, they must be enclosed in brackets:
{ph}
or
{ph2}
dial.tone:
Quote from: azrobert on April 22, 2014, 06:27:21 am
First, check my Reply#64 in this thread about provisioning.
The first thing the Callcentric website tells you to do in setting up the Obi202 is to disable ITSP and ObiTalk provisioning, so I'm good there.
Quote from: azrobert on April 22, 2014, 06:27:21 am
The inbound call route is where you direct calls to phone1 or phone2.
Voice Services -> SP1/2/3/4 Service -> X_InboundCallRoute:
ph
or
ph2
If you have more than 1 rule, they must be enclosed in brackets:
{ph}
or
{ph2}
I checked and the default X_InboundCallRoute setting for SP2, SP3, and SP4 is "ph,ph2" (without the quotes), so that is good, too. However, I didn't see anything for X_OutboundCallRoute; did I miss it?
dial.tone:
Quote from: dial.tone on April 22, 2014, 06:24:44 am
Ok, I just went into the web portal and used the configuration guides provided on the Callcentric and Circlenet websites to configure CC on SP3 and CN on SP4. After the reboot, here is what I got on the status page:
"Register Failed: 401 Unauthorized (server=199.30.56.194:5060; retry in 118s)"
Now that I think about it, in the nearly two years I've owned my Obi202, I've never used or otherwise tested SP3 or SP4, so I have no way of knowing if those channels (or circuits or whatever term is appropriate) even work or not. This simple test seems to indicate they might not. I've always used SP1 (via SimonTelephonics/GV) for my main home phone and SP2 (via GV) for my fax line. When my SP3/SP4 setup attempts (using the ObiTalk wizard) failed before, I latched-onto the idea of using the Voice Gateway method to keep the fax line (incoming and outgoing) on SP2. My thinking was that, if I could get that to work, I would set up my main home phone the same way on SP1. Is there any way my SimonTelephonics/GV setup on SP1 could be interfering with my ability to make SP3/SP4 work? There shouldn't be, since SP2 works. That is, SP2 works for outbound calls if I configure it (via the web portal) with my Circlenet account settings; and it works for incoming calls if I set it up with my Callcentric settings. I really don't know any other way to test SP3/SP4 (other than setting them up as I did and getting the "Register Failed" notice.
azrobert:
"ph,ph2" will ring both Phone Ports. I think you want ph or ph2.
The OutboundCallRoute is found in Physical Interfaces -> Phone Port 1/2
The error you're getting indicates the provider doesn't like the UserID and/or Password.
Are both SP3 and SP4 failing to register?
dial.tone:
Quote from: azrobert on April 22, 2014, 11:28:51 am
"ph,ph2" will ring both Phone Ports. I think you want ph or ph2.
The OutboundCallRoute is found in Physical Interfaces -> Phone Port 1/2
The error you're getting indicates the provider doesn't like the UserID and/or Password.
Are both SP3 and SP4 failing to register?
I double-checked the UserID and Password for both accounts and they are correct. I changed the X_InboundCallRoute on SP3 to ph2. Under Physical Interfaces>Phone2 Port>OutboundCallRoute is the following long string: {([1-9]x?*(Mpli)):pp},{(<##:>):li},{(<#:>):ph1},{(<**70:>(Mli)):li},{(<**82:>(Mbt2)):bt2},{(<**81:>(Mbt)):bt},{(<**8:>(Mbt)):bt},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Msp3)):sp3},{(<**4:>(Msp4)):sp4},{(<**9:>(Mpp)):pp},{(Mpli):pli} so I left it alone. However, I noticed that also on that page is a parameter for PrimaryLine, which was default-set to SP1, so I changed it to SP3. Reboot produced. . ."Register Failed: 401 Unauthorized (server=199.30.56.194:5060; retry in 24s)" for both SP3 and SP4. I will clear out all SP3 and SP4 settings back to their default values and redo the Callcentric and Circlenet setups on SP2, one at a time (Callcentric for inbound calls and Circlenet for outbound calls), just to verify to myself and the world that they (and I) work and post back. In the mean time, and I know this may be asking a lot, could somebody please post a step-by-step, beginning-to-end configuration guide for using the Voice Gateway method for SP2/Phone2 with Callcentric-in and Circlenet-out with copy/paste examples that can't easily be mistaken -- an example that is designed to be implemented today, not after May 15th? I've had additional eyes check my work and we can't find what is wrong with my Voice Gateway setup.
Navigation
[0] Message Index
[#] Next page
[*] Previous page